Panasonic WJ-FS616 Service Manual page 5

7. Multiscreen Selection Button (MULTISCREEN
SELECT)
This button is used to select the multiscreen pattern to
be displayed on the multiscreen monitor while monitor-
ing the camera picture or VTR playback picture.
Pressing this button repeatedly will switch the screen as
follows:
Camera Picture:
4→7→9→10→13→16→4 screen segments
VTR Playback Picture:
4→9→16→4 screen segments
8. Sequence Button (SEQUENCE)
This button is used to activate the sequence mode. In
this mode, a series of camera pictures is displayed in
succession on the monitor screen for the specified dura-
tion.
The LED (Green) in the button lights up to indicate that
this mode is selected.
9. Camera Number Buttons (CAMERA)
Preset Position Number Buttons
(PRESET POSITION)
CAMERA:
These buttons are used to select the desired cam-
era picture.
The LED (Green) in the button lights up to indicate
the camera number presently selected.
PRESET POSITION:
These buttons are used in combination with the
PRE POSI button to assign a preset position num-
ber to the selected camera.
10. VTR / Camera Selection Button (VTR / CAM)
This button is used to select the camera picture or VTR
playback picture to be displayed on the multiscreen
monitor screen.
The LED (Green) in the button lights up to indicate that
the VTR mode is selected.
Note: The above operation is not valid unless multi-
screen output
Multiscreen Monitor button.
11. Control Panel
Press "PUSH OPEN" to open the control panel.
21. Function Button (FUNCTION)
This button is used to display the VTR playback picture
with the camera pictures on the multiscreen monitor.
During the setup, this button is used to select the next
page.
22. Preset Position Button (PRE-POSI)
This button is used to assign a preset position to a
specified camera.
23. Still Button (STILL)
Increment Button (+)
This button is used to still the picture displayed on the
multiscreen monitor.
is selected by pressing
The LED (Green) in the button lights up to indicate that
the still mode is selected.
During the setup, this button is used to select the
desired parameter in the setup menu.
24. Electronic Zoom Button (EL-ZOOM)
Decrement Button (–)
This button is used to zoom the picture presently dis-
played on the multiscreen monitor.
The LED (Green) in the button lights up to indicate that
the zoom mode is selected.
During the setup, this button is used to select the
desired parameter in the setup menu.
25. Home / Set Button (HOME / SET)
This button is used to return to the home position of the
camera.
During the setup, this button is used to display a sub-
menu in the setup menu if the item has its own setting
menu.
26. Direction Arrow Buttons
These buttons are used to operate the Pan/Tilt Head
manually, or to move the cursor to the desired position
in the setup menu of the Video Multiplexer.
UP:
DOWN:
LEFT:
RIGHT:
27. Auto Button (AUTO)
This button is used to activate the auto panning function
when the specified camera is connected.
28. Iris Control Buttons (IRIS, CLOSE / OPEN)
These buttons are used to close or open the lens iris of
the specified lens mounted on the camera.
When these buttons are pressed at the same time, the
lens iris is reset to the factory settings.
29. Focus Control Buttons (FOCUS, NEAR / FAR)
These buttons are used to adjust the lens focus of the
the
specified lens mounted on the camera.
When these buttons are pressed at the same time, the
lens focus is automatically set.
30. Zoom Control Buttons (ZOOM, TELE / WIDE)
These buttons are used to adjust the lens zoom of the
specified lens mounted on the camera.
31. Setup/Escape Button (SETUP / ESC)
This button is used to display the setup menu of the
Video Multiplexer.
During the setup, press this button to execute the cur-
rently selected setting and return to the previous setup
menu.
32. Lock Switch (LOCK OFF / ON)
This switch can be used to lock out operation of the
video multiplexer panel controls.
While this switch is in ON position, control from the
video multiplexer is disabled.
2
Upward
Downward
Left
Right