Uniden FP105 Operating Manual page 15

®
LCD CONTRAST
1. Press and hold the store button for approximately 2 seconds until the display shows
LCD CONTRAST.
2. Press the >> or << buttons to adjust the display contrast to the desired viewing level.
3. Press the store button to set and move to the next menu option or cancel to save and exit.
®
TIME/DATE
1. Press and hold the store button until the display shows LCD CONTRAST.
2. Press the store button again, and the display will show SET TIME/DATE.
3. Press *(am) OR #(pm).
4. Use the keypad buttons to set the time and date manually following the cursor position.
Press the store button to set and move to the next menu option or cancel to save and exit.
Example
:
To set the time and date as 08.45AM on the 9th of July
1. Use the keypad buttons and press * 0 8 4 5 8 9 0 7
2. Press the store button to set and move to the next menu option or cancel to exit,
!
If you make a mistake, use the < < or >> buttons to move the cursor and re-enter the
correct information.
If you subscribe to a Caller ID service, the time and date will be automaticaly updated
when the first C/D information is received, therefore you do not need to set it manually.
®
CALL WAIT ID ON/OFF
1. Press and hold the store button until display shows LCD CONTRAST
2. Press the store button 3 times until the display shows CALL WAIT ID ON,
3. Press the >> or << buttons to choose CALL WAIT ON/OFF
4. Press the store button to set and move to the next menu option or cancel to save and exit.
®
RESET PP CODE I CLEAR SPEED DIAL I NO CHANGES
1. Press and hold the store button until display shows LCD CONTRAST.
2. Press the store button 4 times until the display shows RESET PP CODE.
3. Press the > > or << buttons to choose from the following options;
RESET PP CODE (Resets all pre-programmed codes to factory default),
CLEAR SPEED DIAL (Deletes all stored Speed Dial memories),
NO CHANGES
4. Press the store button to confirm your choice and exit the Options Menu.
!
The Advance User Options Menu can not be accessed if the handset is off the cradle
or if the telephone is in the speaker phone mode.
To exit the Advance User Options Menu at any time, press the
.
cancel
button.
If your Telephone is not performing to your expectations, please try these
simple steps. If you are still unable to resolve the problems, contact Uniden
Customer Service for assistance.
Problem Suggestion
Can't make or receive Make sure you use only the line cord
l
supplied with this telephone.
calls.
Check that both ends of the telephone
l
line cord and Handset cord are plugged in.
Can't hear the telephone Make sure you do not have too many
l
ringing. telephones connected to the telephone line.
Adjust the Ringer Volume to either lo/hi.
l
Plug another telephone into the telephone
l
socket and check for a dial tone.
Speakerphone Volume During speakerphone conversation, adjust
l
too low. the speakervolume slider control on the side
of the telephone.
One Touch Speed Dial Repeat the memory storage procedures
l
Numbers are not working detailed on page 15.
correctly.
Handset does not hang Make sure the Handset Retainer Tab has
l
been turned around (point facing up)
up in the wall mount
position. and the Handset is placed firmly into the
cradle.
New Call LED keeps All new calls must be reviewed before
l
the new call LED stops flashing.
flashing
Review and clear message bank messages.
Message LED keeps
l
flashing.
Caller ID feature not These are all subscription or user pays
l
working services. To subscribe, or check the
pricing and availability, please contact
Message Bank feature
Telstra Residential Sales and Service on
not working
Call Diversion feature not '13 2200 or Telstra Business on ' 1 3 2000
working
Display information is This can happen due to power interruption.
l
incomplete or frozen. Reset your phone by pushing the reset
button (tiny switch located at the rear side of
the base).
Telstra is a registered trademark of Telstra Corporation Limited ACN 051 775 556