Table of Contents
Advertisement
Battery Replacement and Handling
Recharge your phone on a regular basis by returning the handset to either
cradle after each phone call. When the operating time becomes short even
after a battery is recharged, please replace the battery. With normal usage,
your battery should last about one year. To order replacement batteries,
please contact Uniden's Parts Department. The contact information is listed
on the back cover page.
Warning:
To avoid the risk of personal injury or property damage from fire or
electrical shock, only use the Uniden battery model and Uniden adapter
model specifically designated for this product.
Caution:
•
Use only the specified Uniden battery pack (BT-1006).
•
Do not remove the battery from the handset to charge it.
•
Never throw the battery into a fire, disassemble it, or heat it.
•
Do not remove or damage the battery casing.
Cleaning the Battery Charging Contacts
To maintain a good charge, clean the charging
contacts on the handset once a month. Dampen a
cloth with plain water.
Gently rub the damp cloth over the charging contacts
until all visible dirt is removed. Dry the contacts
thoroughly before returning the handset to the cradle.
Caution:
Do not use paint thinner, alcohol, or other
chemical products. Doing so may discolor the
surface of the telephone and damage the finish.
13) Troubleshooting
Re-registering Handsets
There are a few cases when it may be necessary to re-register your
handsets to the base:
•
When you want to change the digital security code. (Refer to "Changing
the Digital Security Code".)
•
When there is a power failure that lasts more than one hour.
•
If a handset's battery is completely discharged. (The handset must be
recharged for - 20 hours before re-registering to the base.)
•
Any time you experience difficulty connecting to the base to place or
receive calls.
To re-register handsets:
)
Pick up the handset from the base. Press and hold [find handset] on the
base.
While holding [find handset], place the handset in the base. The charge/
2)
in use LED on the base begins to flash, indicating the base is registering
the handset. Wait for at least five seconds.
3)
Pick up the handset from the base and press [talk/flash]. If the display
shows TALK, the handset is registered. If not, place the handset in the
base to try again.
4)
Press [end].
)
Place the next handset in the base and wait for at least five seconds.
No need to hold [find handset] this time.
)
Repeat steps 3 - with any other handsets you have.
Changing the Digital Security Code
The digital security code is an identification code used to connect the handset
and the base. If the handset battery pack is completely discharged or the
battery pack is removed, the digital security code will be lost. If this happens,
a new security code is set automatically the next time the battery pack is
charged in the base. In the rare situation that you suspect another cordless
telephone is using the same security code, you can change the code.
To change the digital security code, re-register both handsets to the base
following the instructions in "Re-registering Handsets" above.
Note: Any handsets that are not properly re-register may not be
able to communicate with the base.
Traveling Out-of-Range
During a call, as you begin to move your handset too far from your base
noise increases. If you pass the range limits of the base, your call will
terminate within one minute.
Solving Common Issues
If your phone is not performing to your expectations, please try these simple
steps first. If these steps do not solve your problem, please call our Customer
Hotline. See back cover page for contact information.
Symptom
The charge/in
use LED or
LED
won't illuminate
when the handset
is placed in the
cradle.
•
Make sure the AC adapter is plugged into the base or
charger and wall outlet.
•
Make sure the handset is properly seated in the
cradle.
•
Make sure the charging contacts on the handsets are
clean.
Contacts
Contacts
Suggestion
Advertisement
Table of Contents
