Warnings - Banner Sure Cross DXM1200-Bx Instruction Manual

Wireless controller

Hide thumbs Also See for Sure Cross DXM1200-Bx:

Instruction manual (66 pages)

Table of Contents

Sure Cross

DXM1200-Bx Wireless Controller

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

may not cause harmful interference, and (2) this device must accept any interference received, including interference

that may cause undesired operation.

10.9 Note

This equipment has been tested and found to comply with the limits for a digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

•

Reorient or relocate the receiving antenna,

•

Increase the separation between the equipment and receiving module,

•

Connect the equipment into an outlet on a circuit different from that to which the receiving module is connected,

and/or

•

Consult the dealer or an experienced radio/TV technician for help.

Antenna Warning: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in

p. 60. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing them

with non-approved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique

antenna connectors), FCC Section 15.247 (emissions), and ISED RSS-Gen Section 6.8.

10.9 FCC and ISED Approved Antennas

WARNING: This equipment is approved only for mobile and base station transmitting devices. Antenna(s) used for this

transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated

or operating in conjunction with any other antenna or transmitter.

The radio transmitter modules DX80-2400 and SX243 have been approved by FCC and ISED Canada to operate with the

antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a

gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Table 3: Certified Antennas for 2.4 GHz

Model

Antenna Type

Integral antenna

BWA-2O2-C

Omni, 1/2 wave dipole,

Swivel

BWA-2O2-D

Omni, Dome, Box Mount

BWA-2O2-E

Omni, 1/4 wave dipole,

Swivel

BWA-2O5-C

Omni, Collinear, Swivel

BWA-2O5-MA

Omni, full-wave dipole, NMO

BWA-2O6-A

Omni, Dome, Box Mount

BWA-2O7-C

Omni, Coaxial Sleeve, Swivel DX80-2400

10.10 Warnings

Install and properly ground a qualified surge suppressor when installing a remote antenna system. Remote antenna configurations installed without surge suppressors

invalidate the manufacturer's warranty. Keep the ground wire as short as possible and make all ground connections to a single-point ground system to ensure no ground loops

are created. No surge suppressor can absorb all lightning strikes; do not touch the Sure Cross

thunderstorm.

Exporting Sure Cross

Radios. It is our intent to fully comply with all national and regional regulations regarding radio frequency emissions. Customers who want to re-export

this product to a country other than that to which it was sold must ensure the device is approved in the destination country. The Sure Cross wireless products were certified

for use in these countries using the antenna that ships with the product. When using other antennas, verify you are not exceeding the transmit power levels allowed by local

governing agencies. This device has been designed to operate with the antennas listed on Banner Engineering's website and having a maximum gain of 9 dBm. Antennas not

included in this list or having a gain greater that 9 dBm are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. To reduce potential radio

interference to other users, the antenna type and its gain should be so chosen such that the equivalent isotropically radiated power (EIRP) is not more than that permitted for

successful communication. Consult with Banner Engineering Corp. if the destination country is not on this list.

2.4 GHz Radio Module

DX80-2400

DX80-2400 or SX243

DX80-2400

www.bannerengineering.com - Tel: + 1 888 373 6767

Maximum Gain

Unity gain

≤ 2 dBi

≤ 5 dBi

≤ 4.5 dBi

≤ 6 dBi