Resetting The Control - Traulsen RBC100 Service Manual

Refers To Older Control Versions Only
If memory reaches capacity during a chill cycle there is potential that some printout data could
be incorrect (date & time). This will reset on it's own, however to do so manually...
STEP 1
MAIN MENU AIR 35
BY TEMP BY PROD
BY TIME
08:05:01 MORE
Main Menu display press MORE
STEP 3
SELECT SUPERVISOR:
↓ ↓ ↓ ↓ ↓ TIM SMITH
↓ ↓ ↓ ↓ ↓ PASSWORD (PIN): 85↑ ↑ ↑ ↑ ↑
CANCEL ENTER
Enter PASSWORD/PIN 85.
STEP 6
FACTORY SETTINGS
VERSION 2.0
S/N:T00000A00
RESET NEXT
Serial number will be
displayed. Press NEXT.
STEP 9
↓ ↓ ↓ ↓ ↓ BLASTING DIFF (4)
↓ ↓ ↓ ↓ ↓ HOLDING DIFF (3) °
↓ ↓ ↓ ↓ ↓ ANTI-SHORT(1)
BACK NEXT
Press NEXT.
STEP 12
↓ ↓ ↓ ↓ ↓ MACH. MODEL (RBC)
↓ ↓ ↓ ↓ ↓ MACHINE SIZE(50)
RESET EXIT
↓ ↓ ↓ ↓ ↓ MACH. MODEL (RBC)
↓ ↓ ↓ ↓ ↓ MACHINE SIZE(50)
RESET EXIT
Display will ask MACHINE SIZE. Press RESET,
then using the UP or DOWN arrow change for
your model. For RBC50 = 50, RBC100 = 100,
RBC200 = 200. Press EXIT.
°
F MAIN MENU
HOLD PROD
DEFROST
BACK
Press the top left, top
↑ ↑ ↑ ↑ ↑
right, and bottom right buttons
at the same time.
↓ ↓ ↓ ↓ ↓ LABEL PRINTER (NO)↑ ↑ ↑ ↑ ↑
RESET
Display will ask LABEL
PRINTER (NO), press the UP
arrow to select YES.
°
F↑ ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ ↓ DEFROST TIME (40)
F ↑ ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ ↓ DEFR. TEMP (50)
↑ ↑ ↑ ↑ ↑ ↓ ↓ ↓ ↓ ↓ DEFR. INTVL (3) HR ↑ ↑ ↑ ↑ ↑
BACK
↑ ↑ ↑ ↑ ↑
↑ ↑ ↑ ↑ ↑
FACTORY SETTINGS
DO YOU WISH TO SAVE
THESE NEW SETTINGS
↑ ↑ ↑ ↑ ↑
NO
↑ ↑ ↑ ↑ ↑

Resetting The Control

STEP 2
08:06:01
PRINT
SETUP
Press SETUP.
STEP 4
STEP 7
NEXT
STEP 10
↑ ↑ ↑ ↑ ↑
° ↑ ↑ ↑ ↑ ↑
F
NEXT
Press NEXT.
STEP 13
YES
Press YES.
DISPLAY WILL SHOW
SELECT SUPERVISOR:
↓ ↓ ↓ ↓ ↓ PRESET SUPERVISOR↑ ↑ ↑ ↑ ↑
↓ ↓ ↓ ↓ ↓ PASSWORD (PIN): 00↑ ↑ ↑ ↑ ↑
CANCEL ENTER
SELECT SUPERVISOR screen
STEP 5
FACTORY SETTINGS
VERSION 2.0
S/N:T00000A00
RESET NEXT
FACTORY SETTINGS
menu. Press RESET.
STEP 8
↓ ↓ ↓ ↓ ↓ LABEL PRINTER(YES)↑ ↑ ↑ ↑ ↑
RESET NEXT
Press NEXT.
STEP 11
ENTER SECURITY CODE
FOR NEXT SETTINGS:
↓ ↓ ↓ ↓ ↓
(000000)
EXIT ENTER
Press ENTER.
(do not change code)
DISPLAY WILL SHOW
NEW SOFTWARE
HAS BEEN INSTALLED
SYSTEM PARAMETERS
HAVE BEEN SET!
14. The display will return to the MAIN
MENU. Repeat steps 1-10
15. Press EXIT.
16. Press YES.
10
↑ ↑ ↑ ↑ ↑