GRAUPNER GM Genius Pro Series Manual page 13

Settable values in the program
Programmable
Parameter Values
Items
Motor Type
Select Battery LiPo / LiFe / NiMH (NiCd)
Disable / Auto / 3.0V ~ 7.5V (Step:0.1V)
Cut Off Voltage
Disable / Auto / 6.0V ~ 23V (Step:0.1V)_S3085
Power Curve 0 ~ 10
Boost
Off
Boost Max+TB
ON
+TH
Boost Min-rpm 0 ~ 64500 (Step: 500 rpm)
Boost Max-rpm 0 ~ 65000 (Step: 500 rpm)
TH
20%
40%
Boost-TH. Limit
60%
80%
100%
Turbo Delay 0.00 ~ 1.00s (Step: 0.05s)
Turbo + Slope 0.00 ~ 1.00s (Step: 0.05s)
Turbo - Slope 0.00 ~ 1.00s (Step: 0.05s)
Acceleration 0 ~ 10
Start Power 0 ~ 100 (Step: 1%)
Start Curr Limit Off, 1% ~ 100% (Step: 1%)
Current Limit Off, 1% ~ 100% (Step: 1%)
Reverse Function One Way / Two Way / Two Way 2 / Two Way 3
Reverse Delay Off / 0.2s / 0.5s / 0.8s / 1.3s / 1.8s / 2.5s
M-Reverse Amount 20 ~ 100% (Step: 1%)
Neutral Width Narrow / Normal / Wide
Motor Direction Normal / Reverse
Brake Response 0% ~ 100% (Step: 1%)
A.B.S. Brake Off / Weakest / Weak / Normal / Strong / Strongest
Drag Brake 0% ~ 100% (Step: 1%)
Min Brake Amount 0% ~ 100% (Step: 1%)
Mid Brake Amount 0% ~ 100% (Step: 1%)
Mid Brake Location 0% ~ 100% (Step: 1%)
Max Brake Amount 0% ~ 100% (Step: 1%)
Soft Brake Hard / Soft
Brake Freq 1KHz / 2KHz / 5KHz / 8KHz / 16KHz / 32KHz
Motor Freq 1KHz / 2KHz / 5KHz / 8KHz / 16KHz / 32KHz
Drag Freq 1KHz / 2KHz / 5KHz / 8KHz / 16KHz / 32KHz
Cut Off Temp 100° ~ 135° (Step: 5) / Disable
Cut Off M-Temp 100° ~ 135° (Step: 5) / Disable
B.E.C. Voltage 6.0 / 7.4V
Current Voltage XX.X
Current Temp 100° ~ 135°
Max Temperature 100° ~ 135°
Motor Temp 100° ~ 135°
Motor Max Temp 100° ~ 135°
Max Current 0 A ~ 999 A
Motor Pole Num 2 ~ 20 Pole
Gear ratio 2.0 : 1 ~ 15.0 : 1
Tire Diameter 40mm ~ 200mm
Motor-Wiring A-B-C / C-B-A
Maximum Speed XXX.X Km/h
Maximum RPM XXX rpm
Error History M, T1, T2, S, V, R
Download All parameters inside the setup card are downloaded to the ESC.
Restore Memory All setting information inside EEPROM are read via the RAM.
Backup Memory All setting information inside the RAM are stored at EEPROM
Factory Setting Change the setting of ESC to default status.
S3084_S3086_S3078_S3085_MP_V1
Sensor only for S3084,S3086,S3078
Max
X
0 ~ 58 (Hybrid:25)
0 ~ 58 (Hybrid:25)
Limit
0 ~ 58 (Hybrid:25)
0 ~ 58 (Hybrid:25)
0 ~ 58 (Hybrid:25)
0 ~ 58 (Hybrid:25)
0 ~ 58 (Hybrid:25)
Hybrid only for S3078,S3086,S3085
+ TB
X
0 ~ 58 (Hybrid:25)
0 ~ 58 (Hybrid:25)
Soft
8KHz / 16KHz
Default
Sensor
LiPo
Auto
5
Off
5000 rpm
25000
rpm
0
0.20s
0.20s
0.20s
5
0%
Off
Off
One Way
2.5s
100%
Wide
Normal
0%
Off
0%
30%
50%
50%
100%
Soft
1KHz
5KHz
1KHz
135°
135°
6.0V
2 Pole
2.0 : 1
63mm
A-B-C
13 / 32