Audio Ch. 5/6-11/12 Screen - Roland VR-50HD MK II Reference Manual

Audio Ch. 5/6–11/12 Screen
These settings adjust the input audio of channels 5/6–11/12.
Menu item Value
(bold text: default value)
Turns the Audio Follow function on/off. Audio follow is a function that automatically switches the audio output in tandem with video
switching.
* If the Video Follows Audio function (p. 16) is on, this function automatically turns off and cannot be specified.
Follow
OFF
ON
Solo OFF, ON
Mute OFF, ON
Input MIC, LINE, VIDEO
A.Gain (*1) 0 0– +68.0dB
0– +42.0dB
D.Gain -42.0–0
Level -Inf– +10.0dB
HPF OFF, ON
Delay 0 0–500.0ms
Left, L49–L01,
Pan (*1)
R01–R49, Right
Converts the input audio from stereo to mono.
OFF
Mono (*2)
L MONO
R MONO
LR MIX
AUX 1 Send -Inf– +10.0dB
Specifies the position from which the audio sent to the AUX 1 bus is taken.
Send Point
Pre
Post
Unity —
AUX 2 Send -Inf– +10.0dB
Specifies the position from which the audio sent to the AUX 2 bus is taken.
Send Point Pre
Post
Unity —
Reverb Send 0–127
(*1) Only for channels 5/6 and 7/8. This can be set if "Input" is "MIC. "
(*2) This can be set if "Input" is "LINE" or "VIDEO. "
Gate When you touch <Edit>, a detailed screen for the effect appears.
OFF, ON
Gate
Threshold -80– -48–0dB
Release 30–500–5000ms
(Press a channel 5/6–11/12 [SELECT] button, or [MENU] button 0 Audio <5/6>–<11/12>)
Explanation
The audio is always output regardless of the video selection.
The audio is output only when the video corresponding to the audio channel is selected. The audio is
automatically muted if another video is selected.
Turns the solo function on/off. Only the audio for which this is "ON" is heard in the headphones.
Turns the mute function on/off. If this is "ON, " the audio is temporarily silenced.
Selects the audio source that is input to the channel. If "VIDEO" is selected, channels 1 and 2 of the SDI or
HDMI embedded audio are input.
Value Ch. 5/6
MIC MIC 5
LINE
LINE 1
HDMI IN 1
VIDEO
SDI IN 1
Adjusts the input gain (sensitivity) in the analog domain.
* This can also be adjusted by the [MIC 5 GAIN] or [MIC 7 GAIN] knobs.
Adjusts the input gain (sensitivity) in the digital domain (after conversion from analog to digital).
Adjusts the input volume.
* This can also be adjusted by the channel fader.
Turns the high-pass filter on/off.
Effect Cuts off unneeded low-band audio. The cutoff frequency is 80 Hz.
Adjusts the delay time of the audio. Delays the output of the audio by the specified time.
Center
Adjusts the stereo position (pan).
Sends the stereo input audio to the audio bus without change.
The audio of the L channel is sent to both L and R of the audio bus.
The audio of the R channel is sent to both L and R of the audio bus.
The audio of the L channel and R channel is mixed, and sent to both L and R of the audio bus.
Adjusts the amount of audio sent to the AUX 1 bus.
Send the audio before it is adjusted by the fader (pre-fader).
Send the audio after it passes through the fader (post-fader).
Sets "AUX 1 Send" to unity (0.0 dB).
Adjusts the amount of audio sent to the AUX 2 bus.
Send the audio before it is adjusted by the fader (pre-fader).
Send the audio after it passes through the fader (post-fader).
Sets "AUX 2 Send" to unity (0.0 dB).
Adjusts the amount of audio sent to reverb.
Turns the gate on/off.
Eliminates audio that is lower than the specified threshold level. This is effective when the
Effect noise that you want to remove is separate from the audio that you want to keep, and can be
used to remove hiss or other noise that is heard during periods of silence.
Specifies the level used as the threshold for removing audio.
Specifies the length of time until the audio is fully attenuated after audio falls below the threshold.
Ch. 7/8 Ch. 9/10 Ch. 11/12
MIC 7 — —
LINE 2 LINE 3 LINE 4
HDMI IN 2 HDMI IN 3 HDMI IN 4
SDI IN 2 SDI IN 3 SDI IN 4
Menu List
39