Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Metra Electronics Manuals
  4. Automobile Accessories
  5. 99-7392B
  6. Installation instructions manual

Metra Electronics 99-7392B Installation Instructions Manual

Hyundai kona2018-up
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
KIT COMPONENTS
• A) Radio housing (front) • B) Radio housing (rear) • C) Radio brackets • D) Pioneer adapter brackets • E) Pocket • F) (4) #4 x 3/8" Phillips screws
• G) (6) #8 x 3/8" Phillips screws • H) Panel clip
A
B
Metra. The World's Best Kits.
®
Hyundai Kona
Visit
MetraOnline.com
for more detailed information about the product and up-to-date vehicle
specific applications
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision †
• Pioneer modular DDIN radio provision †
• Painted matte black
† This kit can only be used with an ISO DDIN radio with an "L" shaped chassis design, with the radio
chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued,
replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios,
DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.
C
D
G
F
MetraOnline.com
2018-up
E
H
© COPYRIGHT 2019 METRA ELECTRONICS CORPORATION
99-7392B
I N S TA L L AT I O N I N S T R U C T I O N S

TABLE OF CONTENTS

Dash Disassembly ..................................................2
Kit Preparation .......................................................3
-ISO DDIN radio provision......................................5
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring harness: 70-7306
Antenna adapter: 40-KI11
Steering wheel control interface: ASWC-1
12v to 6v camera step-down: AX-CAM6V
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
Attention!
Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
REV. 6/21/19 INST99-7392B

Advertisement

loading

Related Manuals for Metra Electronics 99-7392B

Summary of Contents for Metra Electronics 99-7392B

  • Page 1: Table Of Contents

    When testing the aftermarket equipment, ensure that all factory equipment is connected before cycling the key to ignition. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 6/21/19 INST99-7392B...

  • Page 2: Dash Disassembly

    DASH DISASSEMBLY 1. Unclip and remove the speedometer cluster bezel, and the top trim from the steering column. These will come out as one piece, connected by material. (Figure A) 2. Unclip and remove the entire panel that houses the center and right a/c vent. (Figure B) Continue to Kit Preparation (Figure A)

  • Page 3: Kit Preparation

    KIT PREPARATION 1. Remove the top trim piece behind the radio: a. Unclip the (3) clips securing the front of the trim. (Figure A) b. Slide the trim to the left, then up and slightly back to release the trim. A little finesse is required with this process.

  • Page 4: Kit Assembly

    KIT ASSEMBLY ISO DIN radio provision with pocket 6. Secure the radio housing (rear) to the radio assembly using (4) #4 x 3/8” 1. Secure the radio brackets to the pocket Phillips screws provided. (Figure D) using (2) #8 x 3/8” Phillips screws 7.

  • Page 5: Iso Ddin Radio Provision

    KIT ASSEMBLY ISO DDIN radio provision 5. Locate the factory wiring harness and antenna connector in the dash and 1. Attach the panel clip provided onto the complete all necessary connections to radio housing (front). the radio. Metra recommends using the 2. Secure the radio brackets to the radio proper mating adapter from Metra housing (front) using (4) #8 x 3/8”...

  • Page 6: Pioneer Modular Ddin Radio Provision

    KIT ASSEMBLY Pioneer Modular DDIN radio provision 4. Secure the display/bracket assembly to the radio chassis using (4) screws Note: For steps 3 and 4, reference the supplied with the radio. (Figure C) installation manual provided with the 5. Slide the radio assembly into the radio for which hardware to use.
  • Page 7 KIT ASSEMBLY (CONT.) 6. Secure the radio housing (rear) to the radio assembly using (4) #4 x 3/8” Phillips screws provided. (Figure E) 7. Locate the factory wiring harness and antenna connector in the dash and complete all necessary connections to the radio.
  • Page 8 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 6/21/19 INST99-7392B...