Positioning The Gun Arm Assembly; Horizontal Position Of The Second Gun; Horizontal Position Of The First Gun - Graco LINE LAZER A Series Instructions And Parts List

Positioning the Gun Arm Assembly

PUMP SIDE
1
402
6
Fig. 13
The gun arms can be positioned for a variety of spraying
needs. The drawings on page 20 primarily show the guns
mounted on the pump side of the Linestriper . However,
one or both guns may be mounted on the engine side.
Whenever You Move the Guns
CAUTION
Do not kink the cables, which could prevent them
from properly triggering and untriggering the guns.
Disengage the trigger cables and engage the gun trigger
safety latch first. See page 22. Do not kink the trigger
cables. Pull out more of the 50 ft. hose, if necessary.
After moving the guns, reposition the spray tip guard so
it is parallel to the ground and its "wings" face the front
and back of the unit. Disengage the gun trigger safety
latch and engage the trigger cable.
Vertical Position of the First or Second Gun
Loosen the arm clamp (6) and move the gun up or down.
Tighten the clamp. Engage the trigger cable.

Horizontal Position of the First Gun

Method 1: Disengage the trigger cable. Loosen the car-
riage clamps (B,D) and slide the carriage bar (4) left or
right, so the gun will be outside the tire path. Tighten the
clamps. Engage the trigger cable.
Method 2: Disengage the trigger cable. Loosen the arm
clamp (6) and rotate the gun out to the side. Tighten the
bolt. Engage the trigger cable.
NOTE: Use methods 1 and 2 together to obtain the max-
imum distance of one gun from the unit, which is helpful
when spraying around obstacles.
B
4
405A
93
404
"WINGS" OF TIP GUARD

Horizontal Position of the Second Gun

Method 1: Disengage the trigger cable. Loosen the
clamps (405A, 405B). Slide the second gun bar (404)
horizontally, being sure both clamps engage the second
gun bar. Tighten the clamps. Engage the trigger cable.
Method 2: Disengage the trigger cable. Loosen the arm
clamp (6) and rotate the gun out to the side. Tighten the
bolt. Engage the trigger cable.
NOTE: Use methods 1 and 2 together to obtain the max-
imum distance of 33–
of two guns.
Mount Guns on the Engine Side of the Cart
1. For both guns, disengage the trigger cable and en-
gage the trigger safety latch. See page 22.
2. Loosen the gun holder knobs (93) and remove the
gun. Lay the guns out of the way.
3. Remove the knobs (E) on both carriage clamps
(B,D); the carriage bar (4) and extension clamps (A)
will drop down. See Fig. 13, DETAIL A.
4. Lift the front tire and rotate the carriage bar 180 un-
der the cart and to the other side of it.
5. Position the carriage bar below the carriage clamps
(B,D). Align the holes in the top of the extension
clamps (A) with the holes in the carriage bar clamps
and install the knobs (E). See Fig. 13, DETAIL A.
6. Loosen the post/arm clamps (5) and rotate the guns
forward. Retighten the clamps.
7. Install the guns. Note to which gun and position on
the dual gun selector each of the cables (1 and 402)
goes. Route the hoses and cables carefully to pre-
vent kinking. Position the spray tip guards. Disen-
gage the gun trigger safety latches. Engage the trig-
ger cables.
ENGINE SIDE
D
405B
DETAIL A
E
B
A
1
/ in. (851 mm) between the center
2
D
02158