Advertisement
ASSEMBLY INSTRUCTIONS
q Attaching the Handlebar
1
Loosen the collar clamp and slide
it upward on the handlebar. With a
twisting motion, push the handlebar
onto the fork until it bottoms out on
the fork headset lock nut.
REPAIR / SERVICE
q Attaching the Wheels
1
2
Front wheel sequence.
Securely tighten the bolt
as shown.
q Replacing the Tires/Tubes
1
2
Completly deflate the tire. Use a
Assemble the core using the
5mm Allen wrench to remove all four
diagram at right. Tighten using
fastener bolts on the core. Remove
your 5mm Allen wrench and then
the worn/damaged tire or inner tube
inflate. (Do not exceed 100 psi)
and replace it with a new one.
CHECK BEFORE RIDING
q Collar Clamp
q Tires
Using a 5mm Allen wrench, check that the clamp bolts are tightened securely.
Check the running pressure of your tires and inspect them for any signs of damage.
Check your front and rear bolts to ensure they are tight.
Diamond DirtScoot_MAN_US_1306_v.1.indd 3-4
2
With the front wheel pointed straight
ahead, the handlebars square to the front
wheel and the Phase Two logo facing the
front, tighten the clamp as shown. Alternately
tighten each bolt until securely tightened.
3
4
Rear wheel sequence.
Securely tighten the bolt
as shown.
Bearings
Wheel Hub
Fastener Bolts
Spacer
Inner Tube
Outer Tire
Bearings
WARNING: Failure to
properly install and tighten the
clamp may cause the rider to
lose control and fall. If you do not
understand these instructions or the
concept of "tighten securely", seek
the assistance of a qualified mechanic.
3
CHECK BEFORE RIDING
q Wheels and Bearings
Under normal circumstances and conditions, Dirt Scoot wheels and wheel bearings are maintenance free. Nonetheless,
it is the responsibility of the owner or guardian to periodically inspect the wheels for wear and tear, the axle for proper
tightness, and bearings for side-to-side play and loose parts. When a wheel or wheel bearing develops play, this is an
indication of excess wear and replacement is necessary. Replace immediately with only genuine Dirt Scoot replacement
wheels. Worn wheels/bearings are considered normal wear and tear and are not covered by the Warranty. Other
manufacturers' wheels may not be compatible with your Dirt Scoot, may affect your safety and will void your warranty.
q Cleaning Your Scooter
Wipe with a damp cloth to remove dirt and dust.
Do not use industrial cleaners or solvents as they may damage the surfaces. Do not use alcohol, alcohol-based or
ammonia-based cleaners as they may damage or dissolve the plastic components or soften the decals or decal adhesive.
To clean griptape, use a wet coarse bristle brush to scrub any dirt stuck to the surface and let dry.
q How to Ride
Place one foot on the baseboard, push forward with the other foot. Steer. For enhanced cornering, lean slightly into the
direction of the turn. For controlled stops, apply the brake by stepping on the rear fender/brake. Practice applying the
brake at various speeds and in an open area free from obstructions before riding around others.
SAFETY REMINDERS
PRE-RIDE CHECKLIST
q
Loose Parts / Tire Care
Check and secure all fasteners before every ride. Make
sure the clamp is locked properly in place before riding.
Inspect tires for signs of wear or damage. Measure and
adjust the psi of the tires accordingly. Do not exceed 100 psi.
q
Replacement Parts
Replace worn or broken parts immediately. Visit
www.razor.com for replacement parts.
q
Safety Gear
Always wear proper protective equipment, such as an approved
safety helmet, elbow pads and kneepads. Always wear shoes
(lace-up with rubber soles). Keep shoelaces tied and out of the
way of the wheels and never ride barefoot or in sandals.
DO NOT RETURN TO STORE
Failure to follow these instructions may damage
your product and void your warranty.
Need Help? Visit our website for replacement parts, product support and a list of authorized service centers
at www.razor.com or call toll free 866-467-2967 Monday - Friday 8AM - 5PM Pacific Time. Please have the
product I.D. code (located on the white label on your product) available for better assistance.
File Name: DirtScoot_MAN_US_1208_v1r6 | Flat: 420 mm W x 594 mm H | Final: (A4) 210 mm W x 297 mm H
# of Pgs: 8 | Bleed: Yes/pg 1/3 sides | Color: 2 sides, 1/1, 1C | Bindery: Cut, Score and Fold | Date:
PM: Lupe Figueroa | Designer: Antoinette Bing Zaté | NOTES:
WARNING: Wheelies
and other stunt-type riding
reduces your ability to maneuver
and control your scooter. Take
the necessary precautions,
such as wearing appropriate
protective gear and practice in
an area safe for stunt riding and
free from obstructions.
q
Be Careful!
You will see people on TV and maybe even people you know doing
tricks and stunts. These are people who have been practicing on
scooters for a very long time. Don't try something until you are
ready. Avoid steep inclines and don't ride too fast — you can lose
control and fall. Never ride in traffic or on the street and watch
your surroundings for pedestrians, bikers, boarders and skaters.
Maintain a hold on the handlebars at all times.
4
08/29/12
6/6/13 12:09 PM
Advertisement
