Table of Contents
Advertisement
Appendix
Main Specifications
Roland S-2416: STAGE UNIT
Number of Channels
AD Conversion
DA Conversion
Frequency Response
Total Harmonic Distortion + Noise
Dynamic Range
Channel Separation (1 kHz)
Nominal Input Level (Variable)
Non Clip Maximum Input Level
Input Impedance
Nominal Output Level
Maximum Output Level
Output Impedance
Recommended Load Impedance
Residual Noise Level (IHF-A, typ.)
Equivalent Input Noise Level (E.I.N.)
Network Latency
Connectors
Power Consumption
Dimensions
Weight
Operation Temperature
Accessories
*1 When a REAC Splitter S-4000D or a switching hub is used in-line with REAC cables, the network latency will increase by the amount of processing delay introduced
by the splitting device itself. The actual delay is dependant upon the specifications of the splitting device, though the maximum delay amount for a single splitting
device should be about 200 µs.
* 0 dBu = 0.775 Vrms
* In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
24
32 in 24 out
Sample Rate: 96.0 kHz, 48 kHz, 44.1 kHz
Signal Processing: 24 bits
Sample Rate: 96.0 kHz, 48 kHz, 44.1 kHz
Signal Processing: 24 bits
-2 dB / +0 dB (@ +4 dBu, 20 Hz to 40 kHz, Sample Rate: 96 kHz, typ.)
-2 dB / +0 dB (@ +4 dBu, 20 Hz to 20 kHz, Sample Rate: 48 kHz / 44.1 kHz, typ.)
0.007 % (Pad: Off, Input Gain: -10 dBu, 20 Hz–20 kHz, typ.)
INPUT jacks (1–24): 110 dB (typ.)
INPUT jacks (1–24): 103 dB (Input Gain: +4 dBu, IHF-A, typ.)
OUTPUT jacks (1–16): 110 dB (typ.)
-65–-10 dBu (PAD: Off )
-45–+10 dBu (PAD: On)
INPUT jacks (1–24): +28 dBu (1 kHz, 10 kΩ load, typ.)
INPUT jacks (1–24): 7 kΩ
OUTPUT jacks (1–16): +4 dBu (Load impedance: 10 kΩ, typ.)
OUTPUT jacks (1–16): +22 dBu (Load impedance: 10 kΩ, typ.)
OUTPUT jacks (1–16): 600 Ω (typ.)
OUTPUT jacks (1–16): 10 kΩ or greater
OUTPUT jacks (1–16): -84 dBu
INPUT jacks (1–24): -128 dB (Input Gain: -65 dBu, IHF-A, typ.)
375 µs when using REAC cable only (AD to REAC to DA Latency: about 1.2 ms) *1
INPUT jacks (1–24):
XLR type, balanced, phantom power
OUTPUT jacks (1–16):
XLR type, balanced
AES/EBU connector:
DB-25 type
REAC port:
RJ-45 EtherCon type
WORD CLOCK connector:
BNC type
REMOTE connector:
DB-9 type
COMPUTER port:
USB type B
* XLR type: 1 GND, 2 HOT, 3 COLD
* Phantom power: DC +48 V (unloaded maximum), 14 mA (maximum load) (All XLR type inputs)
62 W
482 (W) x 348 (D) x 177 (H) mm
19 (W) x 13-3/4 (D) x 7 (H) inches
(EIA-4U rack mountable)
9.7 kg
21 lbs 7 oz
+0–+40 degrees Celsius
+32–+104 degrees Fahrenheit
Power cord
Owner's manual
Rubber foot x 4
Advertisement
Table of Contents
