Erasing Tracks; Erasing A Whole Disc; Refreshing A Disc - Tascam CC-222MK Owner's Manual

6- After recording After recording

Erasing tracks

It is possible to erase the last recorded track, the last
two recorded tracks, the last three recorded tracks, etc.
It is not, however, possible to erase tracks in the "mid-
dle" of the disc.
1 With the disc loaded, and the unit in stop mode,
press the ERASE key.
2 If the display does not show
where is the number of the last track
XX-XX
recorded on the disc, turn the
the keys until it is displayed.
SKIP
3 Turn the MULTI DIAL
change the number of the first track to be erased.
The highest value that this number can take is
the last track recorded (for example, if 17 tracks
have been recorded on the disc, 17-17 means that
the last track only, number 17, will be erased).
The lowest value that this number can take is 2
(if this number was 1, the whole disc would be
erased, as described below). If you do not want
to proceed with the erase operation, press the
key or key.
ERASE STOP

Erasing a whole disc

When you want to erase a whole disc (all the tracks on a
disc), follow the procedure below:
1 With the disc loaded, and the unit in stop mode,
press the ERASE key.
2 Turn the
MULTI DIAL
the display shows
ERASE DISC?
If you do not want to proceed with the erase op-
eration, press the
ERASE
3 To erase the contents of the disc, press the
or the key.
DIAL ENTER

Refreshing a disc

If a CD-RW disc has been corrupted at any point (e.g.
power has been cut off in the middle of a finalize opera-
tion, etc.), or has been used in a computer or another
piece of equipment that makes it unreadable, it is pos-
sible to "refresh" the disc to make it usable again.
1 With the disc loaded, and the unit in stop mode,
press the ERASE key.
2 Turn the MULTI DIAL
the display shows
DISC REFRESH?
3 To refresh the disc, press the
key.
ENTER
If you do not want to proceed with the refresh
operation, press the ERASE

TASCAM CC-222MKIII
,
ERASE XX-XX?
MULTI DIAL or use
or use the SKIP keys to
or use the keys until
SKIP
.
key or key.
STOP
MULTI
or use the SKIP keys until
.
MULTI DIAL or the
key or STOP key.
NOTE
If only one track has been recorded on the disc,
only the "erase disc" option (see "Erasing a whole
disc"on page 28) is available.
4 When the range of tracks to be erased has been
selected, press the MULTI DIAL
key.
NOTE
This operation cannot be undone. If you are going
to erase a track or tracks, make sure that they are
recordings that you really want to erase!
If the erase operation has been selected, the word
flashes on the display, and the timer starts
ERASE
counting down.
At the end of the countdown period, the word
appears briefly on the display, and the
Complete
display returns to the track/time display.
NOTE
This operation cannot be undone. If you are going
to erase a disc, make sure that it contains only
recordings that you really want to erase!
If the erase operation has been selected, the word
flashes on the display, and the timer starts
ERASE
counting down a time value shown on the dis-
play.
At the end of the countdown period, the word
appears briefly on the display, and the
Complete
display returns to the track/time display.
NOTE
This operation cannot be undone. If you are going
to refresh a disc, make sure that it contains only
recordings that you really want to erase!
If the refresh operation has been selected, the
words are shown on the display,
ERASE XX:XX
and the timer starts counting down.
At the end of the countdown period, the word
Complete appears briefly on the display, and
the display returns to the track/time display (of
course, there are no tracks, and the disc is at the
start, with the total time of the disc available for
recording).
or the ENTER