Advertisement
Table of Contents
- 1 Revision Record
- 2 General Information
- 3 Components
- 4 Installing on a Cash Drawer
- 5 Installation Procedures
- 6 Installing on a Counter Top
- 7 Installing the Keyboard
- 8 Installing the Transaction Printer
- 9 Installing the LCD Customer Display
- 10 Cable Routing
- 11 Installing the 2X20 Customer Display
- 12 Installing the Realpos XR7 POS Terminal
- 13 Installing the Swing Arm Skirts
- Download this manual
Advertisement
Table of Contents
Related Manuals for NCR RealPOS XR7
Summary of Contents for NCR RealPOS XR7
- Page 1 KIT INSTRUCTIONS RealPOS Integration Tray 7702-K304 Issue D...
- Page 2 NCR, therefore, reserves the right to change specifications without prior notice. All features, functions, and operations described herein may not be marketed by NCR in all parts of the world. In some instances, photographs are of equipment prototypes. Therefore, before using this document, consult with your NCR representative or NCR office for information that is applicable and current.
- Page 3 RealPOS Integration Tray Introduction The Integration Tray kit provides the necessary components for integrating a printer, keyboard, and Customer Display with the RealPOS terminal. It can be mounted on a flat surface or on a cash drawer.
- Page 4 RealPOS XR7 Integration Tray Kit Instructions Components...
- Page 5 RealPOS XR7 Integration Tray Kit Instructions Installation Procedures The Integration Tray can be installed on an NCR 2181 Cash Drawer or it can be installed directly onto a counter top. Installing on a Cash Drawer 1. Position the Tray Support Bracket on a Cash Drawer and secure it using the supplied screws (4).
- Page 6 RealPOS XR7 Integration Tray Kit Instructions Installing on a Counter Top 1. Position the Tray Support Bracket on the counter top and secure it with screws (4) that are appropriate for the surface type. Note: The mounting holes for the 3rd-party mount much be located toward the rear of the unit.
- Page 7 RealPOS XR7 Integration Tray Kit Instructions Installing the Keyboard Note: If a keyboard is not used, insert the Integration Tray Plug into the opening where the keyboard cable would normally be routed. 1. Install the keyboard in the Integration Tray.
- Page 8 RealPOS XR7 Integration Tray Kit Instructions Installing the Transaction Printer The NCR 7167, 7168, 7197, 7198, or 7199 printer can be located on either side of the Integration Tray. Note: The Printer Cable Strain Relief is different on the Release 1.0 and the Series II printers.
- Page 9 RealPOS XR7 Integration Tray Kit Instructions 3. Connect the Printer Cable to the USB and Power connectors. 4. Series II Printers Only: Route the cable through the Cable Strain Relief on the printer as shown.
- Page 10 It will be routed up through the XR7 Mount later when the XR7 is installed. NCR 7197/7198/7199 Only: Install the 7607-K324 Printer Skirt. NCR 7167/7168 Release 1.0 Printers Only: Secure the cable in the Cable Strain Relief in the Integration Tray as shown.
- Page 11 RealPOS XR7 Integration Tray Kit Instructions Installing the LCD Customer Display 1. Secure the Operator Display Base to the Tray Support Bracket with screws (4). Note: A Filler Cap is available for when there is no Customer Display 2. Install the Display Arm onto the Display Base.
- Page 12 RealPOS XR7 Integration Tray Kit Instructions 3. Install the Display Back Plate onto the back of the Customer Display (4 screws).
- Page 13 5. Remove the excess slack in the cables and then install the Display Swing Arm Cover onto the Display Swing Arm. 6. Connect the cables to the display. See the NCR RealPOS X-Series Displays User Guide (B005-0000-2337) for additional information about cable connections.
- Page 14 RealPOS XR7 Integration Tray Kit Instructions Installing the 2x20 Customer Display 1. Install the Customer Display Base with screws (4). Install the post behind or in front of the Operator Display Arm. Note: A Filler Cap is available for when there is no Customer Display 2.
- Page 15 RealPOS XR7 Integration Tray Kit Instructions 3. Route the display cables down through the Customer Display Base and out the back of the cabinet. 4. Route the cable through the Display Swivel and Post.
- Page 16 RealPOS XR7 Integration Tray Kit Instructions 5. Insert the Display Post into the Customer Display Base.
- Page 17 RealPOS XR7 Integration Tray Kit Instructions Installing the RealPOS XR7 POS Terminal The Operator Display can be installed on the front or back on either side of the tray. 1. Separate the 7702-K303 Mount Base of the Display Arm (unscrew Clamp Knob).
- Page 18 RealPOS XR7 Integration Tray Kit Instructions 2. Install the Mount Base in the Integration Tray (4 screws). 3. Remove the Left Pivot Housing and Right Pivot Housing from the Display Arm (1 screw on each).
- Page 19 RealPOS XR7 Integration Tray Kit Instructions 4. Lay the RealPOS XR7 fase down on a protective cloth/foam. 5. Install the Display Arm onto the back of the RealPOS XR7 (4 screws). Install the VESA Plate between the mount and the terminal.
- Page 20 RealPOS XR7 Integration Tray Kit Instructions 7. Replace the Left and Right Pivot Housings. 8. Connect the peripheral, LAN, and power cables to the terminal. Cable Routing The exploded view below shows how to route the cables through the display mount.
- Page 21 RealPOS XR7 Integration Tray Kit Instructions Installing the Swing Arm Skirts 1. Install the Left Swing Arm Skirt. 2. Align the Right Swing Arm Skirt with the Left Swing Arm Skirt and snap it into position.