Siemens SINUMERIK 840D sl Function Manual page 1714

Index
Feedrate override (axis-specific), 1663, 1664,
1665
Feedrate override active, 1660
Feedrate override selected for rapid
traverse, 1661
Fixed stop reached, 1596
Follow up active, 1579
Follow-up mode, 1569, 1570
Gear is changed over, 1638
Hardware limit switches plus and minus, 1590
HMI battery alarm, 1552
HMI CPU1 Ready, 1553
HMI temperature limit, 1552
Interrupt processing active, 1620
Invert M3/M4, 1639
JOG mode, 1601
Key disable, 1557
Key-operated switch position, 1551
Last action block active, 1615
Load, 1564
Load part program, 1559
Lubrication pulse, 1581
M auxiliary function for spindle, 1600
M fct. 1-5 not decoded, 1597
M function for spindle, 1648
M(d) less than M(dx), 1585
M, S, T, D, H, F functions Additional info "Quick"
(quick acknowledgment), 1597
M, S, T, D, H, F functions Modification, 1596
M00/M01 active, 1614, 1615
M02/M30 active, 1616, 1617
Machine function REF, 1604
Machine function REPOS, 1604
Machine function TEACH IN, 1603
Machine-related protection zone
preactivated, 1588
Machine-related protection zone violated, 1589
MDA mode, 1601
Mode change disable, 1560, 1602
Mode group ready, 1607, 1608
Mode group reset, 1603
Mode group stop, 1602
Mode group stop axes plus spindles, 1603
Motor being selected, 1577
Motor/drive data set: Display interface, 1582
Motor/drive data set: Formatting interface, 1586
Motor/drive data set: Request interface, 1576
n(act) equals n(set), 1586
n(act) less than n(min), 1585
n(act) less than n(x), 1585, 1586
NC Ready, 1554
NC Start, 1611
1714
NC Start disable, 1611
NC Stop, 1612
NC Stop at block limit, 1612
NC Stop axes plus spindles, 1612
NCK alarm is active, 1554
NCK alarm with processing stop present, 1566
NCK battery alarm, 1555, 1556
NCK CPU Ready, 1552, 1553
NCU heat sink temperature alarm, 1555
OK, 1562, 1563
Oscillation controlled by the PLC, 1640
Oscillation enable, 1641
Override active, 1666
Part program selection, 1559
Path axis, 1629
PLC action completed, 1610
PLC hard keys, 1558
PLC index, 1559, 1560
PLC line offset, 1560
POS_RESTORED 1, 1635
POS_RESTORED2, 1635
Position controller active, 1580
Position measuring system 1/2 activated, 1592
Position measuring systems 1 and 2, 1570, 1571,
1572
Position reached with exact stop coarse, 1593
Position reached with exact stop fine, 1593
ProgEventDisplay, 1626
Program level abort, 1611
Program status aborted, 1619
Program status interrupted, 1619
Program status running, 1617, 1618
Program status stopped, 1618
Program status wait, 1618
Program test active, 1617
Pulse enable, 1577, 1578
Pulses enabled, 1583
Ramp-function generator disable, 1576
Ramp-function generator disable active, 1582
Rapid traverse override, 1656, 1657, 1658
Rapid traverse override active, 1659
Read-in disable, 1611
Read-in enable is ignored, 1620, 1621
Recall alarm deleted, 1562
Reference point approach delay, 1634
Reference point value 1 to 4, 1633, 1634
Referenced/synchronized 1, 1634
Referenced/synchronized 2, 1635
Referencing active, 1632
Remote diagnosis active, 1551
Repos DEFERAL Chan, 1626
REPOS Delay Ackn, 1628
Function Manual, 01/2015, 6FC5397-0BP40-5BA2
Basic Functions