Siemens SINUMERIK 840D sl Function Manual page 1713

Activate dry run feed, 1652
Activate fixed feedrate 1 - 4 for machine
axes, 1667
Activate fixed feedrate 1 - 4 for path/geometry
axes, 1662
Activate M01, 1609
Activate machine-specific protection zone, 1587
Activate program test, 1610
Activate referencing, 1632
Activate single block, 1609
Activate skip block, 1610
Activate travel to fixed stop, 1595
Active, 1563
Active G function of groups 1 to 60, 1621
Active JOG mode, 1607
Active machine function REF, 1609
Active machine function TEACH IN, 1608
Active mode AUTOMATIC, 1607
Active mode MDA, 1607
Active or passive file system, 1559, 1560
Active REPOS machine function, 1608, 1609
Active spindle control mode, 1648
Active spindle mode oscillation mode, 1647
Active spindle positioning mode, 1647
Actual direction of rotation clockwise, 1646, 1647
Actual gear stage A to C, 1637
Actual values in WCS, 1558
Air temperature alarm, 1555
All axes stationary, 1592
All axes that have to be referenced are
referenced, 1633
All channels in the reset state, 1608
Analog measured value of the clamping
system, 1651
Analog spindle 1, utilization in percent, 1558
Analog spindle 2, utilization in percent, 1558
Approach block active, 1614
Associated M01/M00 active, 1600
ASUB is active, 1626
ASUB is stopped, 1622, 1623
AT box ready, 1552
AUTOMATIC mode, 1601
Axis/spindle disable, 1567, 1568, 1569
Axis/spindle stationary, 1579
Block search active, 1616
Block search via program test is active, 1623
Cancel alarm deleted, 1561
Change gear, 1643
Channel is ready, 1620
Channel number of the machine control panel to
HMI, 1558
Channel status active, 1619
Basic Functions
Function Manual, 01/2015, 6FC5397-0BP40-5BA2
Channel status interrupted, 1619
Channel status reset, 1620
Channel-specific NCK alarm is active, 1565
Channel-specific protection zone
preactivated, 1588
Channel-specific protection zone violated, 1589
Clamping in progress, 1589
Clear cancel alarms, 1557
Clear recall alarms, 1557
Control program branching, 1627
Controller enable, 1573, 1574
Controller parameter set switchover
(request), 1575
Current controller active, 1581
D function 1, 1598
Darken screen, 1556
Delete distance-to-go (axis-specific) / spindle
reset, 1574, 1575
Delete distance-to-go (channel-specific), 1565
Delete S value, 1639
Disable parameter set switchover commands from
NC, 1575
Displayed channel number from HMI, 1562
Drive ready, 1583
Drive test travel enable, 1566
Drive test travel request, 1578
Drives in cyclic operation, 1553
Drives ready, 1553
Dry run feedrate selected, 1661
Emergency stop, 1629, 1630
Emergency stop active, 1631
Enable protection zones, 1587
Enable travel to fixed stop, 1595
Encoder limit frequency exceeded, 1591
Error, 1563
Extended address F functions 1 to 6, 1599
Extended address H functions 1 to 3, 1599
Extended address M functions 1 to 5, 1597
Extended address S functions 1 to 3, 1598
External zero offset, 1629
F auxiliary function for positioning axis, 1600
F function for positioning axis, 1670
FC9 Out\ Active, 1561
FC9 Out\ Done, 1561
FC9 Out\ Error, 1561
FC9 Out\ StartError, 1561
Feed stop (Geometry axis 1 to 3), 1660
Feed stop / spindle stop (axis-specific), 1667,
1668
Feedrate disable, 1659
Feedrate override, 1653, 1654, 1655
Index
1713