Table of Contents
Advertisement
10-4 Items in the Extended Setup Menu
Menu items in the range 900 to 999, relating to digital processing (Continued)
Item number Item name
917
ACTIVE LINE 1080
CONVERT MODE
(Valid only in 59.94i or
29.97PsF mode)
918
SLOW PROCESS MODE
920
SD-SDI H-ANC
CONTROL
(Invalid in 24PsF or
23.98PsF mode)
Sub-item
1
AUDIO 5CH-8CH
2
RP188 ATC
930
DOWN CONVERTER
MODE (Invalid in 24PsF or
23.98PsF mode)
931
DOWN CONVERTER
LETTER BOX MODE
(Invalid in 24PsF or
23.98PsF mode)
932
H CROP POSITION (DC)
(Invalid in 24PsF or
23.98PsF mode)
934
CROSS COLOR (DC)
(Invalid in 24PsF or
23.98PsF mode)
935
DETAIL GAIN (DC)
(Invalid in 24PsF or
23.98PsF mode)
936
LIMITER (DC)
(Invalid in 24PsF or
23.98PsF mode)
937
CRISP THRESHOLD (DC)
(Invalid in 24PsF or
23.98PsF mode)
LEVEL DEPEND
938
THRESHOLD (DC)
(Invalid in 24PsF or
23.98PsF mode)
939
H DETAIL FREQUENCY
(DC) (Invalid in 24PsF or
23.98PsF mode)
10-30
Chapter 10 Setup Menus
Settings
Select the conversion mode for the number of active scan lines.
[conv]: Convert the active scan lines from 1035 to 1080, without changing the
aspect ratio.
panel: Convert the active scan lines from 1035 to 1080. Insert the 1035 lines into
1080 lines, then compress horizontally.
Note
This item is valid only when menu item 018 is set to 1080.
Switch the filter for increasing the vertical resolution during slow-motion playback
on or off.
ON: Increase the vertical resolution in slow-motion playback.
[OFF]: Do not increase the vertical resolution in slow-motion playback.
Note
In the case of HDCAM tapes recorded in PsF mode, this item is invalid.
Select whether or not to add information to the SD output.
[ON]: Add digital audio data channels 5 to 8.
OFF: Do not add digital audio data channels 5 to 8.
[ON]: Add RP188 time code data.
OFF: Do not add RP188 time code data.
Select the down-converter mode.
[crop]: Select the edge-crop mode.
l-box: Select the letter box mode.
squez: Select the squeeze mode.
Select the aspect ratio of the down-converter output when menu item 930 is set to
l-box.
[16:9]: Set the aspect ratio of the HD-SD converter output to 16:9.
14:9: Set the aspect ratio of the HD-SD converter output to 14:9.
13:9: Set the aspect ratio of the HD-SD converter output to 13:9.
Adjust the "H-crop" (the horizontal position when cropping in the edge crop mode)
of the up/down converter output when menu item 930 is set to crop.
–120 to [0] to 120
Carry out the down-converter cross color adjustment.
0 to [8] to 15
Carry out the down-converter image enhancer adjustment. Adjust the sharpness
of edge emphasis.
0 to [20H] to 7FH
Carry out the down-converter image enhancer adjustment.
Adjust the maximum detail level added to emphasize the original signal.
0 to [20H] to 3FH
Carry out the down-converter image enhancer adjustment. Set the threshold
amplitude at which low amplitude signals are not emphasized.
[0] to FH
Carry out the down-converter image enhancer adjustment. Set the luminance
range for edge enhancement.
0 to [8] to FH
Carry out the down-converter image enhancer adjustment. Set the central
frequency for edge enhancement.
2.6MHz to 3.4MHz to [3.9MHz] to 4.6MHz
(Continued)
Advertisement
Table of Contents
