Related Manuals for Clarke X-PRO CAT165
Summary of Contents for Clarke X-PRO CAT165
- Page 1 10MM AIR BELT SANDER MODEL NO: CAT165 PART NO: 3120179 OPERATING & MAINTENANCE INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0417 ISS1...
- Page 2 INTRODUCTION Thank you for purchasing this CLARKE sander. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service.
-
Page 3: General Safety Rules
GENERAL SAFETY RULES CAUTION: FAILURE TO FOLLOW THESE PRECAUTIONS COULD RESULT IN PERSONAL INJURY, AND/OR DAMAGE TO PROPERTY. WORK ENVIRONMENT 1. Keep the work area clean and tidy. 2. Dress appropriately - Do not wear loose clothing or jewellery. Tie long hair out of the way. -
Page 4: Sander-Specific Safety Rules
• Moving to another work area. • Passing the sander to another person. 14. Never use the tool if it is defective or operating abnormally. 15. The tool should be serviced if required, by qualified service personnel. 16. Avoid damaging the sander for example, by applying excessive force of any kind. - Page 5 Your sander has been designed to give long and trouble free service. If, however, having followed the instructions in this booklet carefully, you encounter problems, take the unit to your local CLARKE dealer. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
-
Page 6: Air Supply Requirements
THE COMPRESSED AIR SUPPLY AIR SUPPLY REQUIREMENTS WARNING: COMPRESSED AIR CAN BE DANGEROUS. ENSURE THAT YOU ARE FAMILIAR WITH ALL PRECAUTIONS RELATING TO THE USE OF COMPRESSORS AND COMPRESSED AIR SUPPLY. • Use only clean, dry, regulated compressed air as a power source. •... -
Page 7: Before Use
• Never exceed the maximum operating pressure for the tool. It is recommended that air pressure to this tool does not exceed 90 psi (6.2 bar) at the tool when running. Higher pressures and unclean air will shorten the life of the tool due to faster wear and is a possible safety hazard. -
Page 8: Connecting The Airline
7. Ensure the trigger is NOT depressed when connecting the airline. • Your air tool is now ready for use • You can fit a whip hose with a quick fit coupling if required (available from your Clarke dealer.) OPERATION OPERATING THE SANDER 1. -
Page 9: Disconnecting The Air Supply
• Let the tool do the work. The actual weight of the sander is normally sufficient for efficient sanding. Do not put additional pressure on the sander, which would only slow down the speed of the belt, reducing efficiency and placing an additional burden on the motor. 4. -
Page 10: Abrasive Belts
STORAGE If the tool is to be stored or is idle for longer than 24 hours, run a few drops of Clarke airline oil into the air inlet and depress the trigger in order to lubricate the internal parts. When not in use, the tool should be disconnected from the air supply and stored in a dry place out of the reach of children. -
Page 11: Troubleshooting
2. Motor parts worn. 2. Return to Clarke dealer for repair. 3. Worn or sticking 3. Drip air tool lubricating mechanism due to oil into air inlet. Allow oil lack of lubricant. -
Page 12: Parts Diagram
PARTS DIAGRAM Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 13: Parts List
PARTS LIST Description No Description Sanding Belt End Cap Idler Pulley Bearing 607zz Washer End Plate A Idler Pulley Screw Cylinder Bracket Rotor Blades (set of 5) Tension Bar Rotor Setscrew 3x10 Throttle Lever Countersunk machine screw 3 x 8 Lever Pin Spring Valve Body... -
Page 14: Specification
Vibration Uncertainty K Please note that the details and specifications contained herein are correct at the time of going to print. However CLARKE International reserve the right to change specifications at any time without prior notice. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... -
Page 15: Declaration Of Conformity
DECLARATION OF CONFORMITY Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...