Error Messages - Sony SRX-T105 Operating Instructions Manual

Error Messages

The error messages are displayed in the STATUS MESSAGE window on the left side of projector and the Error display
window of the SRX Controller. If there are two or more messages, a displayed message changes each five seconds. Use
the list below to check the meaning of the error, and consult your Sony dealer. Be sure to inform them of the displayed
messages and their numbers.
No. Error messages
1 INPUT-A POWER ALERT
2 INPUT-B POWER ALERT
3 INPUT-C POWER ALERT
4 INPUT-D POWER ALERT
5 PR-284_1 POWER ALERT
6 PR-284_2 POWER ALERT
7 PR-284_3 POWER ALERT
8 PR-284_4 POWER ALERT
9 24V POWER SUPPLY ALERT
10 16V POWER SUPPLY ALERT
11 PR-284_1 DETACHED
12 SXRD PANEL TEMPERATURE
ALERT
13 LAMP_A FAN ALERT
14 LAMP_B FAN ALERT
15 LAMP_A POWER SUPPLY UNIT
FAN ALERT
16 LAMP_B POWER SUPPLY UNIT
FAN ALERT
17 PR-284 FAN FAILURE
18 OPTICAL UNIT TEMPERATURE
ALERT
19 LAMP_A TEMPERATURE ALERT
20 LAMP_B TEMPERATURE ALERT
21 LAMP_A HOUSE DETACHED
22 LAMP_B HOUSE DETACHED
23 REAR COVER DETACHED
24 LAMP_A POWER SUPPLY UNIT
ALERT
25 LAMP_B POWER SUPPLY UNIT
ALERT
26 LAMP_A IGNITION FAILURE
27 LAMP_B IGNITION FAILURE
28 CPU ALERT
29 MUTING OFF FAILURE
DOUSER OPEN FAILURE
30 INPUT BOARD FAN FAILURE
31 REAR FAN ALERT
32 LOW REAL TIME CLOCK
BATTERY
36
Error Messages
Meaning
Trouble with power of INPUT A board
Trouble with power of INPUT B board
Trouble with power of INPUT C board
Trouble with power of INPUT D board
Trouble with power of PR-284 board at the top
Trouble with power of PR-284 board on the second row
Trouble with power of PR-284 board on the third row
Trouble with power of PR-284 board on the fourth row
The projector has failed to supply 24V power.
The projector has failed to supply 16V power.
The PR-284 board is not attached correctly on the top row.
The temperature of the panels is too high.
Trouble with the sirocco fan for Lamp A, or the harness is disconnected or down.
Trouble with the sirocco fan for Lamp B, or the harness is disconnected or down.
Trouble with the fan for Lamp A power (ballast), or the harness is disconnected or down.
Trouble with the fan for Lamp B power (ballast), or the harness is disconnected or down.
Trouble with the fan for PR-284 board, or the harness is disconnected or down.
The temperature of the optical unit is too high, or the harness is disconnected or down.
The temperature of Lamp A is too high, or the harness is disconnected or down.
The temperature of Lamp B is too high, or the harness is disconnected or down.
The projection lamp house of Lamp A is detached, or the harness is disconnected or down.
The projection lamp house of Lamp B is detached, or the harness is disconnected or down.
The rear cover is open, or the harness is disconnected or down.
Temporary high temperature or some trouble with the power (ballast) of Lamp A
Temporary high temperature or some trouble with the power (ballast) of Lamp B
Lamp A does not turn on.
Lamp B does not turn on.
Trouble with the main CPU (IC301) on the SY-321. Serious trouble
Trouble with opening/shutting of the shutter, or the harness is disconnected or down.
Trouble with the axial fan next to the INPUT A/B/C/D boards, or the harness is
disconnected or down.
Trouble with the huge axial fan at the rear, or the harness is disconnected or down.
The RTC battery (BT201) for the SY-321 board should be replaced.