Sony MZ-N10 Notes: installing & operating OpenMG Service Manual page 15

Sound Skip Check Result Display Mode
This set can display the count of errors that occurred during the
recording/playing for checking.
• Setting method of sound skip check result display
mode
1. Set the test mode (see page 11).
2. Press the key or REC. key, and the playing or re-
N z
cording sound skip check result display mode becomes active
respectively and press the
and then the playing sound skip check result display mode
becomes active where the LCD displays the following.
Remote commander LCD display
000
P * * R * *
Total count of play
system errors (hex.)
3. When the key is pressed, total error count is displayed on
N
the LCD, and each time the
moves down by one as shown below. Also, if the
pressed, the display item moves up by one, then if the
key is pressed, the display in the record mode appears.
When the REC. key is pressed, total error count is dis-
z
played on the LCD, and each time the
the display item moves down by one as shown below. Also, if
the key is pressed, the display item moves up by one,
.
then if the key is pressed, the display in the play mode
N
appears.
Playing sound skip
result display
000 P * * R * *
000 E I B * *
000 S t a t * *
000 A d r s * *
000 B E m p * *
000 # # # # # #
P**R** : Total play/record errors (hex.)
: Counter of sound skip check each item (hex.)
**
###### : 6-digit address where sound was skipped last (hex.)
• Cause of sound skip error
Cause of error
EIB
Stat
Play
Adrs
BEmp
BOvr
Record
Bful
Rtry
4. To quit the sound skip check result display mode and to return
to the test mode (display check mode), press the
key on the remote commander,
>
Total count of record
system errors (hex.)
key is pressed, the display item
>
key is
.
REC.
z
key is pressed,
>
Recording sound skip
result display
000 P * * R * *
000 B O v r * *
000 B f u l * *
000 R t r y * *
000 # # # # # #
Description of error
Sound error correction error
Decoder status error
Address access error
Buffer is empty
Buffer is full, and sounds were
dumped
Buffer capacity becomes less,
and forcible writing occurred
Retry times over
key.
x
Key and Jog Check Mode
This set can check if the set and remote commander function nor-
mally.
• Setting method of key check mode
1. Set the test mode (see page 11).
[T MARK]
2. Pressing the key or
commander for several seconds (about 3 seconds) activates the
key check mode. (At the last two digits, AD value of remote com-
mander key line is displayed in hexadecimal)
Remote commander LCD display
000
** : AD value of the remote commander key
(hexadecimal 00 to FF)
3. When each key on the set and on remote commander is pressed,
its name is displayed on the remote commander LCD. (The
operated position is displayed for 4 seconds after the slide
switch is operated. If any other key is pressed during this dis-
play, the remote commander LCD switches to its name dis-
play)
Example1: When the
>
Remote commander LCD display
000
FF
** : AD value of the remote commander key
(hexadecimal 00 to FF)
Example2: When the
>
pressed:
Remote commander LCD display
000
rFF
** : AD value of the remote commander key
(hexadecimal 00 to FF)
4. When all the keys on the set and on the remote commander are
considered as OK, the following displays are shown for 4 sec-
onds.
Example1: When the keys on the set are considered as OK:
Remote commander LCD display
888
SET OK **
Set LCD display
888
SET OK **
** : AD value of the remote commander key
(hexadecimal 00 to FF)
MZ-N10
[DISPLAY]
key on the remote
**
key on the set is pressed:
**
key on the remote commander is
**
15