Confirming The Version; Data Backup And Restore Operations - Roland Aerophone AE-10 Service Notes

Oct. 2016

Confirming the Version

1.
Turn on the power.
The initial screen (Tone Selection screen) will be displayed.
* The Power Switch is on the right hand side, when you have the body stand up
and see it from the front.
2.
Press MENU (at the bottom).
The Menu screen appears. Press MENU several times on the Menu screen,
or will go up or down.
3.
Press MENU, and let ,
4.
Press until the display stops.
The version is displayed.
* Pressing while holding
5.
Press Tone.
The initial screen returns.
Data Backup and Restore
Operations
User data is of the following two types.
• User Tone (U: 001 – U: 100)
• System settings
Backing Up User Tones
Using the methods described below, you can back up the Tones.
Items Required
• Computer
• USB cable
Backup Procedure
1.
After powered on, connect the USB connector with the computer.
2.
Press MENU.
The Menu screen appears.
3.
If and/or is on the lower side, press MENU and move it to the
upper side.
4.
Press until the display stops.
The version is displayed.
5.
Press MENU.
* At this moment, there is no change on the screen.
6.
Press and hold Oct-2 shown in the diagram and press
let the display show BACK.
fig.oct-button-1.eps
Oct+2
Oct-2
7.
Press Oct+2.
The BACKUP drive appears on the computer's display.
8.
Copy the AEROPHONE.SVD file in the \Aerophone\BACKUP folder in
the BACKUP drive to the computer.
9.
Unmount the BACKUP drive and disconnect the USB cable.
10. Turn off the power.
22
move to the upper side.
will make the Menu items switch faster.
or
Backing Up System Settings
Follow the procedure below to write down on a piece of paper.
1.
Press MENU.
The Menu screen appears.
2.
With ,
sequence, and write down the following parameter values only.
* As for the others, they are Tone Parameters or parameters that can't be saved, so
you don't need to write them down.
Parameter
Volume
M.Tuning
Breath
Speaker
Auto Off
BreatAdj
Bite Adj
BiteSens
MIDI Ch
Restoring the User Tone
Restore Procedure
1. Execute steps 1 through 5 of Backup Procedure that was described
earlier.
2.
Hold down Oct-2 and press
REST.
3.
Press Oct+2.
AE-10's display will show WAIT, and RESTORE drive will appear on the
computer monitor screen.
4.
Copy the backed up file to the root folder of the RESTORE drive.
5.
Unmount the RESTORE drive, and disconnect th USB cable.
The restore operation starts. When the operation finishes, REST will be
displayed.
6.
Turn off the power.
Restoring System Settings
1.
Press MENU.
The Menu screen appears.
2.
While ,
the values written down to be shown.
* If No-file is displayed, start again the procedures from step 1.
3.
Press MENU and let
4.
Press or
and
5.
Press MENU and let
6. Repeat steps 2 through 5 and write down the values for all parameters.
being on the upper side show the parameters in
Value
0 – 10
415.3 – 466.2
L2, L1, M, H1, H2
Off, On, Auto
Off, 5, 30
AUTO, 0 – 100
AUTO -50 – 0 – +50
AUTO -50 – 0 – +50
1 – 16
or , and let the display show
are displayed in the upper side, let the parameters with
, move to the lower side.
and set the values that were written down.
, move to the upper side.
AE-10