Generac Power Systems 6295 Installation Manuallines page 11

+
TURN OFF THE MAIN CIRCUIT BREAKER IN THE LOAD CENTER BEFORE STARTING INSTALLATION.
I. TRANSFER SWITCH INSTALLATION:
A: Surface Mount Installation Using Power Inlet Box (included in models 6295-6296):
1. Select a location on the left or right side of the Load Center to mount transfer switch, as it is provided with 24"
of flexible conduit. Remove the cover to the load center and the cover of the transfer switch, save the screws.
Measure and cut conduit to a length and snap provided fittings on ends. Locate and remove a knockout (KO)
on lower side of load center that matches the conduit fitting size on the wiring harness. After attaching the flex-
ible conduit to both enclosures through one of the bottom or side KOs, hold the transfer switch in position
against the wall on which it is to be mounted, mark the holes on the wall for the anchoring screws and anchor
to wall (anchors not provided). Be sure NOT to stress the flexible conduit, as it may break. [NOTE: The Electri-
cal Non-Metallic Tubing (ENT) provided is UL Listed and recognized by the National Electrical Code (NEC) for
this application. However, some local codes and inspectors may prohibit its use in buildings that exceed (3)
floors above grade.]
2. Fish the pre-assembled wire harness through the conduit. Strip each wire in the wire harness 5/8" and insert
and tighten the wires to the correspondingly marked circuit breakers in the transfer switch. As you attach each
marked wire to the circuit breaker, write the appliance name on the label on the transfer switch cover per the
TABLE 2 CIRCUIT WORKSHEET completed in Step 1. The unmarked BLACK wires in the harness are
inserted into the UTIL MAIN 2-pole breaker in the transfer switch. Attach the WHITE wire to the neutral bar
located on the right side and attach the GREEN wire to the ground bar located on the left side of the transfer
switch.
3. Install appropriately sized conduit, fittings and wire between the Power Inlet Box (Models 6295-6296 only)
mounted on the building exterior and the transfer switch, referring to Power Inlet Box Install Instructions below.
Locate and remove a KO on the right top or side of the transfer switch, pull wire into transfer switch enclosure
and secure wire with fitting. Install the green ground wire into the ground bar on the left, and install the white
neutral wire into neutral bar on the right. Using provided wiring connectors, connect black wire from PIB to
black wiring going to Meter "A". Repeat for red wire from PIB to Meter "B". Note: Models 6296 and 6380 use
current transformers (CTs) connected to the meters; pass the black wire from the PIB through the hole in the
CT connected to the "A" meter before connecting to the "GEN MAIN A" circuit breaker. Repeat for the red wire
from the PIB, passing through the hole in the CT connected to the "B" meter before connecting to the "GEN
MAIN B" circuit breaker. See FIGURE 2 WIRING DIAGRAM. Reinstall the cover to the transfer switch.
4. In the main Load Center, remove the wires from the breakers for the loads that will be relocated to the transfer
switch. Cut each harness wire to a convenient length, strip off 5/8" insulation and connect to the wires removed
from the breakers per TABLE 2 with the provided wire connectors. Remove two adjacent single pole breakers
from which the load wires were removed and install the NEW 60A or 100A 2-pole circuit breaker (as required in
the Other Items Needed section) in their place. Insert the unmarked BLACK wires from the harness into the
new circuit breaker. Terminate the WHITE and GREEN wire in the harness in an open position in the Neutral
and Ground bars respectively. If there is no separate ground bar, insert the GREEN wire into an open position
in the NEUTRAL bar, and tighten.
5. Reinstall the cover to the load center, and turn ON the MAIN breaker in the load center. Turn ON all branch cir-
cuit breakers in both panels. Turn ON the UTIL MAIN in the transfer switch. Check that power is restored to all
appliances. Transfer switch installation is complete.
B. Flush Mounting in New Construction (unfinished walls) Using Power Inlet Box (included in 6295-6296):
1. Install the transfer switch at the same time as the main load center, in adjacent wall stud openings (the transfer
switch enclosure is 14.25" wide and will fit in standard 16" wall framing). Remove the transfer switch dead front
cover, save the screws. Knock out the appropriate mounting slots on the sides of the enclosure and secure to
framing with nails or screws; be sure the front edge of the enclosure extends forward to be flush with the thick-
ness of the finished wallboard.
2. Mark and drill a 2 1/8" diameter hole in the stud between the main load center and the transfer switch, lining up
with the lowest side KO in the load center and near the bottom center KO in the transfer switch. Remove the
KO's, cut the provided conduit to length, snap on the provided fittings to the conduit, push the conduit through
the drilled hole and install the conduit assembly to the KO openings in the main load center and transfer switch.
Transfer Switch Installation Guidelines
Installation
7