Sony HDCU3100 Operating Instructions Manual page 11

k HDCU3100: Option kit mounting port
The optional HKCU-SM30 Single Mode Fiber Connector Kit
can be attached.
For an overview of option kits, see "Option Kits" (page 12).
k HDCU3170: CAMERA TRIAX connector
Used to connect a video camera, using a triax cable. All video
camera signals, including power supply, control, video, and
audio, are sent and received over one triax cable.
l HDCU3100: CAMERA FIBER connector
Used to connect a video camera, using an optical fiber cable.
All video camera signals, including power supply, control,
video, and audio, are sent and received over one optical fiber
cable.
Note
Dust on the connection surface of the optical fiber cable may
result in transmission errors. When not connected, always
cover the end of the connector with the supplied cap.
l HDCU3170: Option kit mounting port
The optional HKCU-SM30 Single Mode Fiber Connector Kit
can be attached.
For an overview of option kits, see "Option Kits" (page 12).
m - AC IN (AC power input) connector
Use the specified AC power cord to connect to an AC power
supply. The AC power cord can be secured to this unit, using
the plug holder (optional).
n INTERCOM/TALLY/IO PORT (intercom / tally / input/
output) connector (D-sub 50-pin)
Used to input and output intercom, tally, and program audio
signals. Connect to the intercom/tally/program audio
connector of the intercom system.
REAR PREVIEW function: Pin 10 is assigned for the output
pin of the REAR PREVIEW function.
o REFERENCE IN/OUT connectors (BNC-type)
Input an HD tri-level reference sync signal or SD reference
signal (black burst signal, or black burst signal with 10-field ID)
to the REFERENCE IN connector.
The input signal is output from the REFERENCE OUT
connector as is (loop-through output). When not using loop-
through output, terminate the unused connector at 75 ohms.
When a sync signal is not input to the REFERENCE IN
connector, an SD composite sync or HD tri-level sync signal
generated by the internal sync signal generator will be output
from the REFERENCE OUT connector.
p INPUT area
1 PROMPTER (tele-prompter input) 1/2 connectors
(BNC-type)
Input the prompter signal of 1 channel or 2 channels
depending on the setting of PROMPTER2/VBS-RET on the
<REAR I/F> page of the SYSTEM CONFIG menu and
PROMPTER CHANNEL MODE on the <TRUNK/
PROMPTER> page of the MAINTENANCE menu. When
PROMPTER2/VBS-RET is set to DISABLE, the input signal is
output from the other connector as-is (loop-through). If loop-
through output is not used, terminate the unused connector at
75 ohms. When PROMPTER2/VBS-RET is set to ENABLE,
both connectors become inputs and they are terminated at
75 ohms inside the unit.
If the signal used is a 1.0 Vp-p, 75-ohm analog signal, it may
be output from the PROMPTER OUT connector of the video
camera with a frequency bandwidth of 5 MHz, regardless of
signal format.
Note
Only the PROMPTER 1 connector functions on the
HDCU3170.
2 VBS-RET (VBS return video input) connector* (BNC-
type)
A single VBS return signal can be received independently.
* This connector doubles as the PROMPTER 2 connector.
The RET selection is made by the return switch of the video
camera. The type of input signal on each line of RET may be
set individually using the setup menu, or using the MSU-1000
series Master Setup Unit. The aspect ratio may also be
selected for SD signals.
For details on setup menu operations, contact a Sony service
or sales representative.
Refer also to the Master Setup Unit manual.
For details on how to select the signal, contact a Sony service
or sales representative.
q SDI I/O (3G/HD-SDI input/output) 1/2/3/4 connectors
(BNC-type)
These can be used as return video inputs, HD prompter
inputs, camera video signal outputs, and HD-TRUNK outputs.
Set them in NETWORK TRUNK on the <TRUNK/
PROMPTER> page of the MAINTENANCE menu according to
the application.
11