United States, European Union and Canada. 3.1 FCC Compliance The 9522A is certified under 47 CFR Part 25 as FCC ID:Q639522AC. It also complies with Parts 2 and 15 of the FCC Regulations. Operation is subject to the condition that this device does not cause harmful interfer- ence.
Page 2 4 Physical Specifications The 9522A is depicted in Figure 1 below. Figure 1: Top View 4.1 Dimensions The overall dimensions of the 9522A and its weight are summarized in Table 1 below. Table 1: Mechanical Dimensions Parameter Value Length (including antenna connector) 216.1mm (8.51”)
4.3 Interface Connectors The 9522A incorporates three interface connectors. • Multi-Interface Connector (located on the end of the 9522A) • Antenna Connector (located on the end of the 9522A; opposite to the multi-interface connector) • Subscriber Identity Module (SIM) Chip Connector (located beneath a cover plate atop the 9522A) 4.3.1 Multi-Interface Connector...
PCM digital audio input to 9522A Signal ground, 0V signal reference and return 4.3.2 Antenna Connector The 9522A provides a single 50 , TNC type antenna connector both transmit and receive. 4.3.3 SIM Chip Reader An integrated SIM chip reader is provided on the 9522A. This connector allows installation of the chip form of the SIM beneath a cover plate on the 9522A housing.
Page 5 4.5 Connector Sealing in Harsh Environments If the 9522A is to be used in a harsh environment with exposure to high humidity or water, the mating of the multi-interface connector must be further sealed to protect from moisture entry. It is recommended that a bead of RTV silicone sealant be placed on the connector mating to the 9522A’s multi-interface connector where shown in Figure 6 below.
6.5 SIM Interface An integrated SIM chip reader is provided on the 9522A. An external SIM card reader may also be interfaced as a peripheral to the 9522A via the DPL bus (control/audio interface). A SIM card in the external reader will take precedence over the SIM chip in the integrated connector when both are present.
The 9522A is intended for integration into a finished product. The integrator of the 9522A is required to connect a power supply, antenna, and user interface to the 9522A. To ensure that the 9522A is correctly installed the following general instructions (sub-section 7.1) are provided for the installer.
The multi-interface connector cable will provide adequate screening from external electromagnetic interference. The 9522A shall not be located in close proximity to sources of extreme temperature which will cause it be operated outside of its temperature specification (-20°C to +60°C).
(the “Purchaser”), or the date such Products are first placed into satellite subscriber service, whichever occurs earliest. Iridium, at its option, shall at no charge to Purchaser, either repair or replace the Product, or refund the purchase price of a Product that does...
Purchaser’s name, address, and telephone number and a written description of the problem. Product that is repaired or replaced under this warranty shall be returned to Purchaser at Iridium’s expense for the freight and insurance, and at Purchaser’s expense for any applicable duties or other charges.
112 or any other distress calling or emergency services, both public of privately operated, acknowledge and agree as a condition of the provision of phone service and equipment by Iridium that they will make no claim, whether in contract, tort or otherwise, against Iridium for bodily injury,...
62425_user_guide 3/23/06 1:55 PM Page 12 E C Directive Declaration of Conformity...
Page 16
62425_user_guide 3/23/06 1:55 PM Page 13 Iridium Satellite LLC Headquarters 6701 Democracy Blvd., Suite 500 Bethesda, MD 20817 USA Phone +1.301.571.6200 Fax +1.301.571.6250 Iridium Satellite LLC 8440 S. River Parkway Tempe, AZ 85284 Toll Free from a landline +1.866.947.4348 Local or International +1.480.752.5155 Fax +1.480.752.1105...