Kenwood TK-3148 Service Manual page 5

2-2. Panel controls
The key on the top and front panel is momentary-type
push buttons. The functions of these keys and knob are ex-
plained below.
q Antenna connector
Connect the antenna here.
w Rotary encoder
e POWER switch/ VOLUME control
Turn clockwise to switch ON the transceiver. Rotate to
adjust the volume. Turn counterclockwise fully to switch
OFF the transceiver.
r Transmit/ Receive indicator
t Auxiliary (orange) key
y Battery pack safety catch
Flip this catch to prevent accidentally pressing the battery
pack release latch.
u Battery pack release latch
Pull back on this latch to release the battery pack.
i PTT (Push-To-Talk) switch
o Side 1 key
!0 Side 2 key
!1 S key
!2 A key
!3 tB key
!4 Cs key
!5 Universal connector
Connect the speaker/ microphone here. Otherwise, keep
the supplied cover in place.
2-3. Key functions
• Trunking mode
w Rotary encoder
Rotate this encoder to select your desired call address
(voice calls/dialing) or status (status calls).
r Transmit indicator
Lights red while transmitting.
t Auxiliary (orange) key (default setting: None)
Press to activate its auxiliary function.
i PTT (Push-To-Talk) switch
Press to transmit. Also press to initiate a call if "PTT to
Initiate Call" has been programmed.
o Side 1 key (default setting: Clear)
Press to activate its auxiliary function.
!0 Side 2 key (default setting: Call)
Press to activate its auxiliary function.
!1 S key (default setting: Status/ Stack)
Press to activate its auxiliary function.
!2 A key (default setting: Function Menu)
Press to activate its auxiliary function.
!3 tB key (default setting: Conventional)
Press to activate its auxiliary function. Also press to scroll
left while viewing stack entries.
!4 Cs key (default setting: Scan)
Press to activate its auxiliary function. Also press to scroll
right while viewing stack entries.
OPERATING FEATURES /
操作特性
2-2. 控制面板
顶部和前面板上的键是触发式按键。有关这些键和旋钮的
功能说明如下。
q 天线连接器
在这里连接天线。
w 旋转编码器
e 电源开关 / 音量控制器
顺时针旋转可接通对讲机电源。旋转调整音量。逆时针旋
转到底可切断对讲机电源。
r 发射 / 接收指示灯
t 辅助 ( 橙黄色 ) 键
y 电池组保险钩
扳上这个保险钩以防止意外按下电池组释放栓。
u 电池组释放闩锁
按下闩锁可取下电池组。
i PTT( 按讲 ) 开关
o 侧面 1 键
!0 侧面 2 键
!1 S 键
!2 A 键
!3 t B 键
!4 C s 键
!5 通用接口
在这里连接扬声器 / 麦克风，否则应把附带的盖板盖上。
2-3. 键功能
• 集群模式
w 旋转编码器
旋转本编码器选择您所需要呼叫的地址 ( 语音呼叫 / 拨号 )
或者状态代码 ( 用于状态呼叫 )。
r 发射指示灯
在发射中点亮红色。
t 辅助 ( 橙黄色 ) 键 ( 初始设定 : 无 )
按下可开启该辅助功能 。
i PTT( 按讲 ) 开关
按下可发射。当编程了"按 P T T 开始呼叫"后，也可按下
开始呼叫。
o 侧面 1 键 ( 初始设定 : 清除 )
按下可开启该功能。
!0 侧面 2 键 ( 初始设定 : 呼叫 )
按下可开启该功能。
!1 S 键 ( 初始设定 : 状态 / 堆栈 )
按下可开启该功能。
!2 A 键 ( 初始设定 : 功能选单 )
按下可开启该功能。
!3 t B 键 ( 初始设定 : 常规 )
按下可开启该功能。 当观察堆栈条目时， 按下可向左侧滚动。
!4 C s 键 ( 初始设定 : 扫描 )
按下可开启该功能。 当观察堆栈条目时， 按下可向右侧滚动。
TK-3148
5