Table of Contents
Advertisement
Test Mode
■ Test mode operating features
This transceiver has a test mode. To enter test mode,
press [A] key and turn power on. Hold [A] key until test
channel No. and test signalling No. appears on LCD. Test
mode can be inhibited by programming. To exit test mode,
switch the power on again. The following functions are
available in test mode.
• Controls
Controls
"FNC" appears
[Side 1]
Release FNC
[Side 2]
Lamp ON/OFF
[S]
FFSK 1200bps
and 2400bps
[A]
Release FNC
[B]
Compander function
ON and OFF.
[C]
Beat shift ON and OFF Changes signalling.
[ENCODER] Release FNC
• LCD indicator
"SCN"
Unused
" "
Lights at Compander ON.
"LO"
Lights at RF Power Low.
"P"
Unused
"MON"
Lights at moniter ON.
"SVC"
Unlock
"
"
Lights at FFSK 2400bps.
"W"
Wide/Narrow
• LED indicator
Red LED
Lights during transmission. Blinks at the low
battery voltage warning.
Green LED
Lights when there is a carrier.
• Sub LCD indicator
"FNC"
appears at Function ON.
■ Frequency and signalling
The set has been adjusted for the frequencies shown in
the following table. When required. re-adjust them following
the adjustment procedure to obtain the frequencies you want
in actual operation.
Frequency (MHz) (C type)
Channel No.
RX frequency
1
370.05
2
350.05
3
389.95
4
370.00
5
370.20
6
370.40
7 ~ 16
ADJUSTMENT /
"FNC" not appears
Monitor ON and OFF.
Wide/Narrow
Sets to the Tuning
mode.
FNC ON.
RF power HIGH and
LOW.
Changes channel.
TX frequency
370.10
350.10
389.90
370.00
370.20
370.40
调整
测试模式
■ 测试模式操作特性
手持机具有测试模式。要进入测试模式，需要按[A]健，然后
接通电源开关。 按住[A]键直到测试信道号码和信令号码出现在
显示器上为止。测试模式可以通过编程禁止使用。要退出测试
模式，需要再次接通电源开关。下述功能在测试模式中有效。
控制
•
控制
显示"FNC"
[侧面 1]
释放 FNC
[侧面 2]
开启 / 关闭指示灯
[S]
FFSK1200bps
和 2400bps
[A]
释放 FNC
[B]
开启和关闭
语音压扩器
[C]
开启和关闭
Beat shift
[ENCODER] 释放 FNC
LCD 显示
•
"SCN"
不用
"
"
语音压扩器开启时点亮
"LO"
射频功率为低时点亮
"P"
不用
"MON"
开启监听时点亮
"SVC"
失锁
"
"
FFSK 为 2400bps 时点亮
"W"
宽 / 窄带
发光二极管指示灯
•
红色发光二极管 发射时发光。电池低压告警时闪动。
绿色发光二极管 有载波时发光。
子显示器指示灯
•
"FNC" 开启功能时显示。
■ 频率和信令
下述表格中频率的设定可以被调整。需要时，可以按照调整
步骤重新设定这些频率，从而获得用户实际操作需要的频率。
频率（MHz） （C 型）
信道号码
RX 频率
1
370.05
2
350.05
3
389.95
4
370.00
5
370.20
6
370.40
7 － 16
TK-3148
不显示"FNC"
开启和关闭监听
宽 / 窄
设定为调谐模式
开启 FNC
射频功率高和低
改变信令
改变信道
TX 频率
370.10
350.10
389.90
370.00
370.20
370.40
39
Advertisement
Table of Contents
