Table of Contents
Advertisement
TK-3148
5-3. KPG-36 description
(PC programming interface cable: Option)
The KPG-36 is required to interface the TK-3148 to the
computer. It has a circuit in its D-subconnector (25-pin) case
that converts the RS-232C logic level to the TTL level.
The KPG-36 connects the universal connector of the TK-
3148 to the computers RS-232C serial port.
5-4. Programming software KPG-74D CPS Description
The KPG-74D CPS is the programming software for the
transceiver supplied on three 3.5" floppy disks. This software
runs under MS-Windows 98/Me/2000/XP on an IBM-PC or
compatible machine.
The data can be input to or read from the transceiver and
edited on the screen. The programmed or edited data can be
printed out. It is also possible to tune the transceiver.
We recommend that install the KPG-74D CPS for example
to hard disk first then use it.
5-5. Programming with IBM PC
If data is transferred to the transceiver from an IBM PC
with the KPG-74D CPS, the destination data (basic radio
information) for each set can be modified. Normally, it is not
necessary to modify the destination data because their values
are determined automatically when the frequency range
(frequency type) is set.
The values should be modified only if necessary. Data can
be programmed into the flash memory in RS-232C format via
the universal connector.
IBM-PC /
6. Firmware Programming Mode
6-1. Preface
Flash memory is mounted on the TK-3148. This allows the
TK-3148 to be upgraded when new features are released in
the future. (For details on how to obtain the firmware, contact
Customer Service.)
6-2. Connection procedure
Connect the TK-3148 to the personal computer (IBM PC or
compatible) with the interface cable (KPG-36). (Connection is
the same as in the PC Mode.)
8
REALIGNMENT /
KPG-74D CPS
Fig. 1 / 图１
模式组合
5-3．KPG-36 说明
（PC 机编程接口电缆∶选件）
TK-3148 需要通过 KPG-36 接口电缆与电脑连接。此接口电
缆的 D 型连接器（25 芯）中有一个将 RS-232C 逻辑电平转换为
TTL 电平的电路。
KPG-36 将 TK-3148 的通用接口连接到电脑的 RS-232C 串口
上。
5-4．编程软件 KPG-74D CPS 说明
KPG-74D CPS 是手持机的编程软件，共 3 张 3.5" 软盘。此软
件的运行环境为 IBM-PC 机或兼容机的 MS-Windows 98/Me/
2000/XP。
数据可以被写入到手持机或从手持机中读取数据，并且能
在屏幕上进行编辑。已被编程或编辑的数据可以打印出来。也
可以调整手持机的指标。
建议用户在使用之前将 KPG-74D CPS 安装到硬盘上。
5-5．使用 IBM 计算机编程
如果从使用KPG-74D CPS软件的IBM计算机将数据发送到手
持机，设定的通信机型号数据（通信机的基本信息）均可被修
改。由于设定频率范围（频率类型）时、型号数据就已被确定
了，所以一般不需要修改型号数据。
只有在必要的情况下才修改型号数据。
RS-232C 格式的数据经由通用接口输入到通信机的闪速存储
器中。
KPG-36
6. 固件编程模式
6-1．前言
Flash Rom 被安装在 TK-3148 上。当将来出现新功能时，允许
TK-3148 升级。 （要了解如何获得固件的详细情况，请与供应商
联系。 ）
6-2．连接步骤
使用编程电缆（KPG-36）将 TK-3148 与计算机（IBM 计算机
或兼容机）连接。 （与计算机编程模式中的连接方法一样。 ）
Advertisement
Table of Contents
