Setting The Tone Signals For Analog Fm Mode; Setting The Tot (Time Out Timer); Setting The Sql Hysteresis - Yaesu DR-1X FR Operating Manual

Vhf/uhf c4fm/fm 50w ams digital repeater
Table of Contents

Advertisement

Setting the tone signals for analog FM mode

Setting the tone frequency
1 Touch [ SETUP ] then touch [ F ] .
2 Touch [ SIGNALING ] , then touch [ TONE SQL FREQ ] .
3 Touch [ ▲ ] or [ ▼ ] .
The set value will change each time [ ▲ ] or [ ▼ ] is touched.
4 Touch [ BACK ] 3 times.
The setting is determined and the display will return to the operation
mode screen.
z Factory default: 100.0 Hz
z Tone frequencies between 67.0 Hz and 254.1 Hz can be selected.
Setting the DCS code
1 Touch [ SETUP ] , then touch [ F ] .
2 Touch [ SIGNALING ] , then touch [ DCS CODE ] .
3 Touch [ ▲ ] or [ ▼ ] .
The set value will change each time [ ▲ ] or [ ▼ ] is touched.
4 Touch [ BACK ] 3 times.
The setting is determined and the display will return to the operation
mode screen.
z Factory default: 023
z DCS codes between 023 and 754 can be selected.

Setting the TOT (time out timer)

1 Touch [ SETUP ] , then touch [ F ] , and then touch [ TIMER ] .
2 Touch [ TOT ] .
The set value will change in the following sequence each time [ TOT ] , [ ▲ ],
or [ ▼ ] is touched.
à "3 min" à "4 min" à "5 min" à "10 min" à "OFF" à
à "30sec" à "1 min" à "1.5 min" à "2 min" à "2.5 min" à
3 Touch [ BACK ] 3 times .
The setting is determined and the display will return to the operation
mode screen.
Factory default: 3 min

Setting the SQL HYSTERESIS

1 Touch [ SETUP ] , then touch [ F ] , and then touch [ TIMER ] .
2 Touch [ SQL HYSTERESIS ] .
The set value will change in the following sequence each time [ SQL
HYSTERESIS], [▲], or [▼] is touched.
à "NORMAL" à "HIGH" à "MAX" à
NORMAL: The squelch open signal level and the squelch close signal
level are the same.
HIGH:
The squelch open signal level is higher than the squelch close
signal level. (Makes squelch less likely to close.)
MAX:
The squelch open signal level is much higher than the squelch close level. (Makes squelch even
less likely to close.)
3 Touch [BACK ] 3 times .
The setting is determined and the display will return to the operation mode screen.
Factory default: NORMAL
S E T U P
U P
L
I
N K
 8
7 
ID MODE
D O W N
L
I
N K
���������
TIMER ID ANNOUNCE
D G - I D
     
SQL
DEVIATION
MODE/REMOTE
ID SET
R - O F F
WIDE
T - O F F
Tx PW R
V
/
M
S Q L
BACK
BACK
H I
S E T U P
U P
L
I
N K
 8
7 
ID MODE
D O W N
L
I
N K
���������
TIMER ID ANNOUNCE
D G - I D
     
SQL
DEVIATION
MODE/REMOTE
ID SET
R - O F F
WIDE
T - O F F
Tx PW R
V
/
M
S Q L
BACK
BACK
H I
S E T U P
U P
L
I
N K
 8
7 
ID MODE
D O W N
L
I
N K
���������
TIMER ID ANNOUNCE
D G - I D
     
SQL
DEVIATION
MODE/REMOTE
ID SET
R - O F F
WIDE
T - O F F
Tx PW R
V
/
M
S Q L
BACK
BACK
H I
S E T U P
U P
L
I
N K
 8
7 
ID MODE
D O W N
L
I
N K
���������
TIMER ID ANNOUNCE
D G - I D
     
SQL
DEVIATION
MODE/REMOTE
ID SET
R - O F F
WIDE
T - O F F
Tx PW R
V
/
M
S Q L
BACK
BACK
H I
F
F
F
F
25

Advertisement

Table of Contents
loading

This manual is also suitable for:

Dr-1xe fr

Table of Contents