General Power Tool Safety Warnings; Save All Warnings And Instructions For Future Reference; Additional Safety Rules For Tool - Makita 2712 Instruction Manual

Hide thumbs Also See for 2712:
Table of Contents

Advertisement

Available languages
  • EN

Available languages

  • ENGLISH, page 1
WARNING:
The figures quoted are emission levels and are not
necessarily safe working levels. Whilst there is a
correlation between the emission and exposure levels,
this cannot be used reliably to determine whether or not
further precautions are required. Factors that influence
the actual level of exposure of the workforce include the
characteristics of the work room and the other sources
of noise etc.i.e. the number of machines and other
adjacent processes. Also the permissible exposure level
can vary from country to country. This information,
however, will enable the user of the machine to make a
better evaluation of the hazard and risk.
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Table Saw
Model No./ Type: 2712
Conforms to the following European Directives:
2006/42/EC, 2006/95/EC, 2004/108/EC
They are manufactured in accordance with the following
Standard or standardized documents:
EN1870-1, EN60204-1, EN55014-1, EN55014-2,
EN61000-3-2, EN61000-3-11
The EC Type-Examination Certificate
No.M6A.13.12.86528.002
The EC Type-Examination per 2006/42/EC was
performed by:
TÜV SÜD Product Service GmbH
Ridlerstraße 65. D-80339 München Germany
Identification No.0123
The Technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
20.12.2013
000331
Yasushi Fukaya
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for
future reference.
Director
ADDITIONAL SAFETY RULES
FOR TOOL
SAVE THESE INSTRUCTIONS.
1.
Wear eye protection.
2.
Do not use the tool in presence of flammable
liquids or gases.
3.
NEVER use the tool with an abrasive cut-off
wheel installed.
4.
Check the blade carefully for cracks or
damage before operation. Replace cracked or
damaged blade immediately.
ENH113-1
5.
Use only saw blades recommended by the
manufacturer and which conform to EN847-1,
and observe that the riving knife must not be
thicker than the width of the cut by the saw
blade and not thinner than the body of the
blade.
6.
Always use accessories recommended in this
manual. Use of improper accessories such as
abrasive cut-off wheels may cause an injury.
7.
Select the correct saw blade for the material
to be cut.
8.
Do not use saw blades manufactured from
high speed steel.
9.
To reduce the emitted noise, always be sure
that the blade is sharp and clean.
10. Use correctly sharpened saw blades. Observe
the maximum speed marked on the saw blade.
11.
Clean the spindle, flanges (especially the
installing
installing the blade. Poor installation may
cause vibration/wobbling or slippage of the
blade.
12. Use saw-blade guard and riving knife for
every operation for which it can be used,
including all through sawing operations.
Always install the blade guard following the
instructions out-lined in this manual. Through
sawing operations are those in which the
blade cuts completely through the workpiece
as in ripping or cross cutting. NEVER use the
tool with a faulty blade guard or secure the
blade guard with a rope, string, etc. Any
irregular operation of the blade guard should
GEA010-1
be corrected immediately.
13. Immediately reattach the guard and riving
knife after completing an operation which
requires removal of the guard.
14. Do not cut metal objects such as nails and
screws. Inspect for and remove all nails,
screws and other foreign material from the
workpiece before operation.
15. Remove wrenches, cut-off pieces, etc. from
the table before the switch is turned on.
16. NEVER wear gloves during operation.
5
surface)
and
hex
ENB122-1
nut
before

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents