Related Manuals for Ariens Sno-Thro 932100-824
Summary of Contents for Ariens Sno-Thro 932100-824
- Page 1 Sno-Thro ® Owner/Operator Manual Models 932100 - 824 932308 - 824 932501 - 724 ENGLISH FRANÇAIS ESPAÑOL 03239301D 3/01 Supercedes 03239301,A,B,C Printed in USA...
- Page 2 Undertecknaren av detta dokument, - Me, allekirjoittaneet, ARIENS COMPANY, certify that the Sno Thrower - certifie que le chasse-neige - bestätigen daß die Schneefräse, verklaren dat de sneeuwschüiver - certifica che lo spazzavere - certifica que el quita nieves - attesterer at sneslynger - bevitner at snøfreseren - försäkrar att snöslungan, vakuutamme, että...
-
Page 3: Controls & Features
CONTROLS AND FEATURES FRANÇAIS 1. Levier d’embrayage de l’entraînement de la traction 2. Levier d’embrayage de l’outil 3. Clé de contact 4. Poire d’amorçage 5. Starter 6. Commande des gaz 7. Sélecteur de vitesses 8. Poignée du démarreur à cordon 9. -
Page 4: Table Of Contents
The contents will provide you with safety affect the performance, durability, or safety of this unit instructions for the safe use of your unit during normal and may void the warranty. Ariens disclaims liability for operation and maintenance. any claims or damages, whether warranty, property... -
Page 5: Safety
4. Review recommended lubrication, maintenance 6. Fill out Original Purchaser Registration Card and and adjustments. return the card to Ariens Company. 5. Review Limited Warranty Policy. SAFETY SAFETY ALERTS SAFETY DECALS AND LOCATIONS Look for these symbols to point out ALWAYS replace missing or damaged Safety Decals. - Page 6 Personal Safety Keep people away from unit while operating. Only trained adults may operate unit. Keep children out of work area and under Training includes actual operation. watchful care of a responsible adult. NEVER operate unit after or during the use of medication, drugs or alcohol.
- Page 7 Use only approved extension cords and receptacles Spark Arrester when starting units equipped with Electric starter. DO This product is equipped with an internal combustion NOT connect electric starter cord to any wiring system type engine. DO NOT use unit on or near any that is not a three wire grounded system.
-
Page 8: Assembly
ASSEMBLY WARNING: AVOID INJURY. Read and understand Assembly/Fuel Safety Rules in Safety section before proceeding. Tools Required: • Open-End Wrenches and/or Adjustable Wrench • Tire Gauge UNPACKING UNIT WARNING: Dropping or tipping over boxed unit could result in personal injury or damage to unit. -
Page 9: Operation
Discharge Chute Crank Fill Engine Fuel Tank Place discharge chute crank rod through bracket on the Refer to Engine Manual for proper type and capacity. handlebar panel and into pinion on discharge chute Check Function of all Controls assembly (724) or universal joint (824) and secure with Ensure unit runs and performs properly. - Page 10 Speed Selector Runners The Speed Selector controls the unit travel in a forward For operation on gravel surface, lower Runners so that or reverse direction when positioned in notch of speed. housing will not pick up gravel. On concrete, blacktop or packed snow surfaces raise Runners so that Forward: Scraper Blade scrapes clean.
- Page 11 Function of Clutches 6. Set throttle to the "Fast" position. IMPORTANT: Check Clutch/Brake function before 7. Grasp starter handle and pull rope out until it each use. If the Impeller does not stop quickly when pulls harder. This is the compression stroke; let the Attachment Clutch Lever is released or there is no the rope rewind slowly.
-
Page 12: Maintenance
MAINTENANCE Ariens Dealers will provide any service or adjustments SERVICE POSITION which may be required to keep your unit operating at Place unit on a flat level surface. Tip unit forward onto peak efficiency. - Page 13 2. Add lubricant if required. Allow oil to drain to level of plug and replace plug. Refer to Engine Manual for detailed instructions. 3. Use only Ariens special gear lubricant L-2 (Part CHECK AUGER GEARCASE Number 00008000). IMPORTANT: Proper oil level must be maintained.
-
Page 14: Service & Adjustments
SERVICE AND ADJUSTMENTS WARNING: AVOID INJURY. Read and understand Maintenance and Service Safety Rules in Safety section before attempting Runner service or adjustments. DISCHARGE CHUTE DEFLECTOR To adjust, loosen then retighten hardware to desired Runner deflector drag force. Hardware DISCHARGE CHUTE OS0481 Figure 5 If Chute does not stay in position while operating,... - Page 15 9. Place new belt onto sheave and while holding 4. Replace traction drive belt and belt guard making brake out of way, tip unit together. sure pulleys align. If alignment is necessary, loosen engine pulley set screws, reposition pulley 10. Replace attachment drive belt in reverse order and retighten set screws.
- Page 16 3 1 /4"- 3 3 /4" 1. Attachment Clutch Lever 2. Handle Grips 3. Traction Drive Clutch 3"- 3 1 /4" 1. Drive Belt Figure 9 2. Brake Shoe and Pad OS0452 Figure 8 OS2030 TRACTION DRIVE CLUTCH ADJUSTMENT To Properly Adjust Attachment Clutch/Impeller Brake: Adjust traction clutch to compensate for wear of friction IMPORTANT: IMPELLER BRAKE MUST DISENGAGE wheel when slippage occurs.
- Page 17 SPEED SELECTOR To replace friction wheel (Figure 12): 1. Stop engine and allow hot parts to cool. To adjust (Figure 11): 2. Disconnect the spark plug wire and secure it 1. Disconnect the speed selector rod from the away from the spark plug. adjustment lever by removing hairpin.
- Page 18 To replace friction wheel (Figure 13): SHEAR BOLTS 1. Stop engine and allow hot parts to cool. IMPORTANT: Use only Ariens Shear Bolts for 2. Disconnect the spark plug wire and secure it replacement. Use of any other type of shear bolt may away from the spark plug.
-
Page 19: Storage
For Replacement: 1. Slide auger outward against roll pin and align hole in shaft with hole in auger (holes in shaft for roll pins and Shear Bolts line up). 2. Drive Shear Bolt through hole (if Shear Bolt was broken this will drive remaining part from shaft). 3. -
Page 20: Service Parts
1. Speed Selector Rod obstructing 1. Place Speed Selector Rod into 2nd or 3rd handlebars. position. handlebars. SERVICE PARTS Be sure to always use genuine Ariens parts to keep your Sno-Thro running like new. Part no. Qty Description 21526500 Spark Plug... -
Page 21: Accessories
Vibration Measure < 2.5 @ Operator Hands < 2.5 < 2.5 ACCESSORIES ATTACHMENTS See your authorized Ariens dealer to add the Order the following parts through your Dealer: additional accessories available to your Sno-Thro. Part No. Qty. Description Part No. Description... -
Page 22: Warranty
Ariens Company warrants to the original purchaser that consumer products manufactured by Ariens Company will be free from defects in material and workmanship for a period of two (2) years after the date of purchase, and will repair any defect in material or... - Page 23 GB - 23...
- Page 24 Ariens Company 655 West Ryan Street P.O. Box 157 Brillion, WI 54110-0157 920-756-2141 Fax 920-756-2407 www.ariens.com...