MULTIQUIP WRS5200 Operation Manual
  1. Manuals
  2. Brands
  3. MULTIQUIP Manuals
  4. Construction Equipment
  5. WRS5200
  6. Operation manual
MULTIQUIP WRS5200 Operation Manual

MULTIQUIP WRS5200 Operation Manual

Ride-on roller screed, kubota wg972-gl-e3 dual fuel, gas and propane engine
Hide thumbs Also See for WRS5200:
Table of Contents

Advertisement

Quick Links

Download this manual
OPERATION MANUAL
MODEL WRS5200
MODEL WRS5200DFPU
RIDE-ON ROLLER SCREED
(KUBOTA WG972-GL-E3 DUAL FUEL)
GAS AND PROPANE ENGINE
Revision #2 (03/08/18)
To find the latest revision of this
publication, visit our website at:
www.multiquip.com
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
PN: 46188

Advertisement

Table of Contents
loading

Related Manuals for MULTIQUIP WRS5200

Summary of Contents for MULTIQUIP WRS5200

  • Page 1 OPERATION MANUAL MODEL WRS5200 MODEL WRS5200DFPU RIDE-ON ROLLER SCREED (KUBOTA WG972-GL-E3 DUAL FUEL) GAS AND PROPANE ENGINE Revision #2 (03/08/18) To find the latest revision of this publication, visit our website at: www.multiquip.com THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

  • Page 2: Proposition 65 Warning

    PROPOSITION 65 WARNING Engine exhaust some its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are: Leadfromlead-basedpaints.

  • Page 3: Silicosis/Respiratory Warnings

    SILICOSIS/RESPIRATORY WARNINGS WARNING WARNING SILICOSIS WARNING RESPIRATORY HAZARDS Grinding/cutting/drilling of masonry, concrete, metal and Grinding/cutting/drilling of masonry, concrete, metal and other materials with silica in their composition may give other materials can generate dust, mists and fumes off dust or mists containing crystalline silica. Silica is a containing chemicals known to cause serious or fatal basic component of sand, quartz, brick clay, granite and injury or illness, such as respiratory disease, cancer,...

  • Page 4: Table Of Contents

    TABLE OF CONTENTS WRS5200/WRSPUDF Ride-On Roller Screed Proposition 65 Warning ........... 2 Silicosis/Respiratory Warnings ........ 3 Table Of Contents ............ 4 Training Checklist ............ 6 Daily Pre-Operation Checklist ......... 7 Safety Information ..........8-14 Transporting And Lifting Procedures ....15-16 Specifications ............
  • Page 5 NOTES PAGE 5 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 6: Training Checklist

    TRAINING CHECKLIST TRAINING CHECKLIST DESCRIPTION DATE Read Operator’s Manual completely. Machine layout, location of components, checking of engine and hydraulic oil levels. Fuel system, refueling procedure. Operation of lights (if equipped). Operation of controls (machine not running). Safety controls. Emergency stop procedures. Startup of machine, engine choke throttle.

  • Page 7: Daily Pre-Operation Checklist

    DAILY PRE-OPERATION CHECKLIST Daily Pre-Operation Checklist       Engine oil level Hydraulic oil level Radiator coolant level Drive tube operation Strike tube operation Safety stop switch operation Steering control operation Operator Trainee COMMENTS PAGE 7 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 8: Safety Information

    SAFETY INFORMATION DO NOT operate or service the equipment before reading Potential hazards associated with the operation of this the entire manual. Safety precautions should be followed equipment will be referenced with hazard symbols which at all times when operating this equipment. may appear throughout this manual in conjunction with Failure to read and understand the safety safety messages.
  • Page 9 „ NEVER use accessories or attachments that are not „ Avoid wearing jewelry or loose fi tting clothes that may recommended by Multiquip for this equipment. Damage snag on the controls or moving parts as this can cause to the equipment and/or injury to user may result.
  • Page 10 SAFETY INFORMATION SCREED SAFETY NOTICE „ ALWAYS keep the machine in proper running condition. DANGER „ Fix damage to machine and replace any broken parts „ Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can immediately.
  • Page 11 SAFETY INFORMATION FUEL SAFETY (LPG/PROPANE) NOTICE „ NEVER run engine without an air fi lter or with a dirty air DANGER fi lter. Severe engine damage may occur. Service air fi lter „ DO NOT fill propane tank within 25 ft. (7.62 m) of frequently to prevent engine malfunction.
  • Page 12 SAFETY INFORMATION „ Frost or LP Gas odor indicates a propane tank leak. „ If the battery liquid (dilute sulfuric acid) comes into contact with eyes, rinse eyes immediately with plenty Inspect or repair immediately. If propane tank is defective DO NOT use.
  • Page 13 SAFETY INFORMATION „ Use adequate lifting cable (wire or rope) of suffi cient „ DOT Requirements include the following: strength. • Connect and test electric brake operation. „ DO NOT lift machine to unnecessary heights. • Secure portable power cables in cable tray with tie „...

  • Page 14: Safety Information

    SAFETY INFORMATION ENVIRONMENTAL SAFETY/DECOMMISSIONING EMISSIONS INFORMATION (GASOLINE) NOTICE NOTICE Decommissioning is a controlled process used to safely The engine used in this equipment is a dual fuel engine retire a piece of equipment that is no longer serviceable. (gasoline/LPG). The gasoline side of the engine has been If the equipment poses an unacceptable and unrepairable designed to reduce harmful levels of carbon monoxide safety risk due to wear or damage or is no longer cost...

  • Page 15: Transporting And Lifting Procedures

    TRANSPORTING AND LIFTING PROCEDURES LIFTING THE SCREED 1. Utilize a spreader bar of proper length and lifting capacity. Secure lifting straps from both ends of the The following procedure and Figure 1 describe how to lift spreader bar to each of the four (4) lift loops on the the screed.
  • Page 16 TRANSPORTING AND LIFTING PROCEDURES TRANSPORTING THE SCREED TRANSPORTING THE POWER UNIT Place the screed on a flatbed truck during transportation. Place the power unit on a flatbed truck during transportation. Elevate tires to ensure that screed rests on rollers. Attach Attach tie-down straps to power unit to prevent movement.

  • Page 17: Specifications

    SPECIFICATIONS Table 1. Roller Screed Specifications 14, 18, 22, 26, 28, 32,36, 40, 52 ft. Available Lengths (4.25, 5.4, 6.7, 7.9, 8.5, 9.7, 10.9, 12.1, 15.8 m) Working Widths 1.2 to 50 ft. (3.6 to15.2 m) Strike Tube Speed 450 RPM Maximum Drive Tube Speed 150 RPM Maximum Weight (Max Length)

  • Page 18: Dimensions (Roller Screed)

    DIMENSIONS (ROLLER SCREED) Figure 5. Roller Screed Dimensions Table 2. Roller Screed Dimensions Reference Dimension ft. (meters) Letter 5 (1.5) 5 (1.5) 14 (4.3), 16 (4.9), 18 (5.5), 22 (6.7), 26 (7.9), 28 (8.5), 30 (9.1), 32 (9.8), 36 (11), 40 (12.2), 44 (13.4), 48 (14.6) and 52 (15.8) 3.8 (1.2) 6.5 (2.0)

  • Page 19: Dimensions (Power Unit)

    DIMENSIONS (POWER UNIT) Figure 6. Power Unit Dimensions (WRSPDU) Table 3. Power Unit Dimensions Reference Dimension in. (mm.) Letter 30.25 (768.35) 28.25 (717.55) 42 (1066.8) 31.13 (790.7) 61.5 (1562.1) 52.5 (1333.5) PAGE 19 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 20: General Information

    GENERAL INFORMATION Truss Sections The MQ WRS5200 Ride-On Roller Screed is a self- propelled SuperScreed that is hydraulically driven and The SuperScreed is composed of truss sections which requires only one operator, two laborers and two concrete vary in length from 3 ft. (1 m) to 9 ft. (2.75 m). These truss placers.
  • Page 21 Proper job planning is essential to a successful application. Screed Rails The WRS5200 Super Screed weighs approximately Screed rails and supports, independent of slab edge 4000 lbs. (1,814 kg.) at a maximum length of 52 ft.

  • Page 22: General Information

    Misuse is defined as the following but not limited to: „ Modifications or repairs made to the equipment without written approval from Multiquip. „ Improper storage „ Poor maintenance „ Dirty machine „...
  • Page 23 NOTES PAGE 23 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 24: General Information

    GENERAL INFORMATION ADJUSTABLE DISC CHAIR WOOD FORM NOTES: CHECK WITH CITY AND STATE CIVIL ENGINEERING REGULATIONS REGARDING THE TYPE AND SIZE LUMBER USED FOR EDGE FORMS. 3/16" (.1875) WALL THICKNESS 2.5" X 2.5" STEEL TUBE RAIL Figure 8. SuperScreed Application PAGE 24 —...

  • Page 25: General Information

    NOTICE adjustable disc chair configuration. Spacing of adjustable disc chairs should be spaced at Figure 8 illustrates Multiquip's recommended way of rail and disc chair placement. ALWAYS check with city 3 foot intervals. This will allow for 1/16-inch deflection in and state civil engineering regulations before installing steel rail tube.

  • Page 26: Ride-On Roller Screed Components

    RIDE-ON ROLLER SCREED COMPONENTS Figure 10. Screed Components 4. Drive Tube Lever (Engine Side) — When activated this The definitions below describe the controls and functions 3-position lever will cause the engine side drive tube of the Ride-On Power Screed (Figure 10). to rotate in a clockwise (forward) or counterclockwise 1.
  • Page 27 RIDE-ON ROLLER SCREED COMPONENTS 6. Drive Tube Speed Control Lever — Controls the 18. Locking Pin — To prevent movement of the power variable speed of the drive tubes. 150 rpm max. This unit and the possibility of the power unit falling from lever should be in the straight up position when the platform during operation, insert screed locking pin starting the engine.

  • Page 28: Power Unit Components

    POWER UNIT COMPONENTS 14-PIN RECEPTACLE 1 / 2 Figure 11. Power Unit Components PAGE 28 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 29: Power Unit Components

    POWER UNIT COMPONENTS The definitions below describe the controls and functions 13. Hydraulic Reservoir Tank/Cap — Remove this of the Power Unit (Figure 11). cap to add hydraulic fluid. Fill with AW MV ISO 46 type hydraulic fluid. Reservoir capacity is 5 gallons 1.

  • Page 30: Control Box Components

    CONTROL BOX COMPONENTS 6. Engine Status Gauge — Multi Cluster gauge, indicates the following: a. Low Oil Pressure LED — When ON indicates that the oil pressure has dropped to 11.4 psi (78.6 kPa). This condition will cause the engine to shutdown. During normal operation of the pump this LED should remain OFF.

  • Page 31: Engine Components

    ENGINE COMPONENTS Figure 13. Kubota WG972-GL-E3 Engine 11. V-belt — ALWAYS make sure the V-belt is properly The engine (Figure 13) must be checked for proper tensioned. A loose or defective V-belt can adversely lubrication and filled with fuel prior to operation. Refer to the affect the performance of the engine.

  • Page 32: Roller Screed Assembly

    ROLLER SCREED ASSEMBLY Roller Screed Assembly Task 1: Operator's End Truss Sections (Reference Figure 14) The following will be required for the assembly of the screed: 1. Locate the 6 ft. (1.8 m) right-side section of truss B. „ Wrenches/Allen Wrenches This truss section can be identified by the R14 marking „...
  • Page 33 ROLLER SCREED ASSEMBLY Figure 14. Operator's Right-Side Truss Sections (14 FT./4.26M) PAGE 33 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)
  • Page 34 ROLLER SCREED ASSEMBLY Task 2: Middle Truss Sections (Reference Figure 15) 1. Locate the 8 ft. (2.4 m) right-side section of truss D. This truss section can be identified by the RM8 marking on the top pipe. 2. Next locate the other 8 ft. (2.4 m) left-side section of truss E.
  • Page 35 ROLLER SCREED ASSEMBLY 16224 16222T 36227 Figure 15. Middle Truss Sections (16 FT./4.87 Meters) PAGE 35 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)
  • Page 36 ROLLER SCREED ASSEMBLY Task 5: Engine End Truss Sections (Reference Task 6: Bearing Installation Figure 16) If the strike tube bearing has not been installed onto the middle bracket perform the following: 1. Locate the 9 ft. (2.75 m) left-side section of truss F. This truss section can be identified by the L14 marking 1.
  • Page 37 ROLLER SCREED ASSEMBLY 16224 16222T 36227 Figure 16. Engine End Left Truss Sections (14 ft./4.25 meters) PAGE 37 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)
  • Page 38 ROLLER SCREED ASSEMBLY Task 7: Strike Tube Assembly Strike Tube Installation (Middle Bracket) 1. Locate middle bracket, P/N 16653 (Figure 18) plate The roller screed used in this example will require different on operator's end of screed. Make sure bearings (2) lengths of strike tubes.
  • Page 39 ROLLER SCREED ASSEMBLY Strike Tube Installation (Middle Section) The 14ft. (4.25 meters) strike tube section should now be attached to the matching section of truss (Figure 19). The following section will illustrate inserting the middle section strike tube. 1. The first middle bracket should now be installed with the splined shaft supporting one end of the 14 ft.
  • Page 40 ROLLER SCREED ASSEMBLY Strike Tube Installation (Engine End) 3. Verify that the strike tube bearing has been (Figure 20) mounted on outer plate at engine end of the screed. If The 16 ft. (4.87 meters) strike tube section should now bearing has not been installed, please see next step.
  • Page 41 ROLLER SCREED ASSEMBLY Task 8: Strike Tube Motor Mounting 6. With the coupler fully engaged, adjust the strike tube guide pins in or out using the guide pin jam nuts so that For initial setup the strike tube motor can be located on the hair pin clip fits snug against the outer plate wall.
  • Page 42 ROLLER SCREED ASSEMBLY Task 9: Hydraulic Hoses There are four hydraulic hoses that need to be routed from the stack and speed control valves at the operator's end of the screed to the drive tube motors (power unit end) and power unit.
  • Page 43 ROLLER SCREED ASSEMBLY Task 10: Control Box Connections 3. Locate the 55 ft. (16.76 meters) power cable P/N 46158. Route this cable (Figure 27) from the control The following instructions illustrate the placement of the box thru the trusses to the 14-pin receptacle located control box onto the operator's platform and the connection on the power unit.
  • Page 44 ROLLER SCREED ASSEMBLY Task 11: Strike Tube Control Cable 4. If installing a control cable of a different length, remove the ball socket end of the control cable from the ball The following instructions illustrate the installation of the stud. strike tube control cable.
  • Page 45 ROLLER SCREED ASSEMBLY Task 12: Tarp Installation Figure 29 illustrates the installation of the tarps (protective covers) onto the various truss sections. Place the tarps on the appropriate sections. All tarps were made to full length per each section of truss. Make sure tarps are securely fasten to the truss frame so that they will not come loose during operation.
  • Page 46 ROLLER SCREED ASSEMBLY Task 13: Scraper Bars The following instructions illustrate the installation of the scraper bars onto the operator and power unit frame The following instructions illustrate the installation of the sections. scraper bars onto the truss sections. 1. Locate scraper bar that corresponds to the operators 1.

  • Page 47: Inspection

    INSPECTION The following instructions are intended as a basic guide for machine start-up and operation. Following these instructions will help preserve and maintain the life of this equipment. BEFORE STARTING Fuel Check (Gasoline) DO NOT smoke while refueling, gasoline/propane fuel is highly flammable and can be dangerous if mishandled.
  • Page 48 INSPECTION Procedure For Filling Propane Tank (In-Place) 12. STOP dispenser/storage tank pump. 13. Disconnect LP Gas dispenser/storage gas line nozzle 1. Remove all combustible materials including dry grass from propane tank fill port. and leaves within 25 ft. (7.62 meters) of LPG dispenser. 14.

  • Page 49: Operation

    OPERATION Hydraulic Oil Check INITIAL STARTING 1. On the power unit place the operation valve lever 1. To check the hydraulic oil level, place the power unit on (Figure 39) in the screed position. a secure flat surface with the engine stopped. 2.
  • Page 50 OPERATION 5. Place the drive tube speed control lever in the straight 4. Press the THROTTLE rocker switch downward and up position. verify that the engine speed is set to idle mode, GREEN light is OFF (Figure 45). 6. Place the strike tube speed and directional control lever in the neutral (center) position.
  • Page 51 OPERATION 4. OPEN propane tank gas valve (Figure 49). Turn valve 10. Press the THROTTLE rocker switch upward (Figure 47) knob counterclockwise to open valve. on the control box and verify that the engine speed is set to full speed mode, GREEN light is ON. THROTTLE SWITCH GREEN LIGHT...
  • Page 52 OPERATION NORMAL SHUTDOWN OPERATION 1. Press down on the THROTTLE switch and listen for 1. Fully engage the operator end directional drive tube the engine speed to decrese (idle). No GREEN light. control lever in the forward direction. 2. Place the two drive tube directional control levers in 2.

  • Page 53: Maintenance

    MAINTENANCE Table 4. Engine Maintenance Schedule EVERY 6 EVERY BEFORE FIRST EVERY 2 DESCRIPTION MONTHS YEAR OPERATION EACH MONTH OR YEARS OR OR 100 OR 300 50 HRS. 500 HRS. HRS. HRS. Check Engine Oil Change Engine Oil Filter Replace Every 200 Hrs.
  • Page 54 MAINTENANCE General maintenance practices are crucial to the CAUTION performance and longevity of your screed. This equipment ALWAYS disconnect the spark plug wire from the spark requires routine cleaning, truss sections inspection, plug and secure away from the engine before performing lubrication and V-belt inspection for wear and damage.
  • Page 55 MAINTENANCE OIL FILTER 2. Remove air filter element from air filter body. 3. Blow compressed air not exceeding 30 psi (205 kPa, 1. Be sure to coat the seal of the new oil filter with clean 2.1 kgf/cm2) through the filter element from the inside engine oil.
  • Page 56 MAINTENANCE SPARK PLUG OIL SOAKED NOTICE NEVER use a spark plug of incorrect heat range. 1. Remove and clean spark plug (Figure 55) with a wire brush if it is to be reused. Discard spark plug if the insulator is cracked or chipped. CORD FAILURE GLAZED 2.
  • Page 57 MAINTENANCE RADIATOR/COOLING SYSTEM WARNING Allow engine to cool when flushing out radiator. Flushing the radiator while hot could cause serious burns from water or steam. 1. Check and clean radiator fins. 2. Check cooling water. 3. Check radiator hoses for fatigue or cracking. 4.
  • Page 58 MAINTENANCE Mishandling of the battery shortens its service life and adds LPG System to maintenance cost. „ Run the engine at idle speed and use a soap solution 1. Check and clean battery terminals for corrosion. or its equivalent to check all LPG connections for leaks between the fuel tank and the dual fuel carburetor.
  • Page 59 MAINTENANCE HYDRAULIC OIL SYSTEM Changing Hydraulic Oil and Filters The hydraulic system consists of a hydraulic pump directly 1. Place the power unit on a clean flat work area and set coupled to the engine. the parking brake. Hydraulic oil is filtered by a screen filter located in the tank 2.
  • Page 60 MAINTENANCE SCREED CLEANUP 4. Place the three-way control valve lever on the power unit to the “Pressure Washer” position as indicated by NEVER allow any concrete to harden on the roller screed. the decal. Immediately after each use, wash any concrete off the 5.
  • Page 61 MAINTENANCE LONG TERM STORAGE For storage of the screed for over 30 days, the following is recommended: „ Drain fuel tank completely, or add STA-BIL to the fuel. „ Run the engine until fuel in the fuel system is completely consumed.

  • Page 62: Troubleshooting (Screed)

    TROUBLESHOOTING (SCREED) Table 7. Screed Troubleshooting Symptom Possible Problem Solution Make sure that the kill switch is Kill switch malfunction? functioning properly. Replace switch if necessary. Look at the fuel system. Make sure there is fuel being supplied to the engine. Fuel? Engine running rough or not at all Check to ensure the fuel filter is not...

  • Page 63: Troubleshooting (Engine)

    TROUBLESHOOTING (ENGINE) Table 8. Engine Troubleshooting Symptom Possible Problem Solution Defective fuel pump? Replace fuel pump. Fuel filter clogged? Replace fuel filter and clean tank. Faulty fuel supply line? Replace or repair fuel line. Check piston, cylinder and valves. Compression too low? Adjust or repair per engine repair manual.

  • Page 64: Troubleshooting (Pressure Washer)

    TROUBLESHOOTING (PRESSURE WASHER) Table 9. Pressure Washer Troubleshooting Symptom Possible Problem Solution The pump is not primed. Prime the pump. Check for air leaks and reseal the inlet Air leaks in the suction line. fittings. Inspect the strainer and remove any Blocked or clogged line strainer.

  • Page 65: Pressure Washer Hydraulic Diagram (Option)

    PRESSURE WASHER HYDRAULIC DIAGRAM (OPTION) CLOSED CENTER SYSTEM HOOKUP 5000 PSI 1800 Series Pressure Washer and Gun Assembly HYDRAULIC WATER TANK SUPPLY Table 10. Pressure Washer Specifications Pressure Gauge 5000 psi (35,000 kPa) Motor inlet and Outlet 1/2" NPT (F) Water Inlet 3/4"...
  • Page 66 NOTES PAGE 66 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 67: Hydraulic Hoses

    HYDRAULIC HOSES Refer to Hydraulic Hoses Layout, next page. Reference Parts Manual P/N 36861 for hose part numbers. Table 11. Hydraulic Hoses Destination Item Number From Stack Valve Port B Drive Tube Motor C, Port C1 Stack Valve Port A Drive Tube Motor A, Port A1 Stack Valve Port D Drive Tube Motor D, Port D1...

  • Page 68: Hydraulic Hoses Layout

    HYDRAULIC HOSES LAYOUT Refer to Table 11 For Hydraulic Hose Layout descriptions. HYDRAULIC TANK HYDRAULIC INTERFACE PLATE TANK STRIKE TUBE INTERFACE HYDRAULIC PLATE FILTER (IN) HYDRAULIC PUMP LOOP FLUSHING VALVE PRESSURE WASHER INTERFACE PLATE CONTROL VALVE OUTER PLATE (ENGINE END) NOTES HOSES TO BE ROUTED THROUGH TRUSSES TO POWER UNIT END...

  • Page 69: Hydraulic Hoseslayout

    HYDRAULIC HOSES LAYOUT STACK VALVE SPEED CONTROL VALVE OPERATOR END (RIDER GUARD) SOLENOID VALVE HYDRAULIC TANK DRIVE TUBE MOTORS E END) HYDRAULIC FILTER (OUT) PAGE 69 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 70: Hydraulic Schematic

    HYDRAULIC SCHEMATIC DRIVE SPEED ROLLER CONTROL MOTOR VALVE DRIVE ROLLER MOTOR DRIVE ROLLER MOTOR 2000 PSI RELIEF VALVE DRIVE ROLLER MOTOR 3-WAY CONTROL VALVE MANUAL HIGH DIRECTIONAL PRESSURE CONTROL VALVE WASHER 1500 PSI RELIEF LOOP FLUSHING VALVE SHUTTLE VALVE TANDEM PUMP ASSEMBLY STRIKE TUBE...

  • Page 71: Hydraulic Locator

    HYDRAULIC LOCATOR STRIKE TUBE INTERFACE PLATE SPEED HYDRAULIC LOOP CONTROL TANK FLUSHING VALVE VALVE TANDEM PUMP ASSY STRIKE TUBE MOTOR PLATE COOLER 3-WAY CONTROL VALVE PRESSURE WASHER INTERFACE PLATE STACK VALVE PRESSURE WASHER PAGE 71 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 72: Control Box Wiring Locator

    CONTROL BOX WIRING LOCATOR REFERENCE CONTROL BOX REAR VIEW WIRING DIAGRAM CONTROL BOX TB21 TB1-4 TB5-8 TB9-12 TB13-16 TB17-21 SOLENOID VALVE PAGE 72 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 73: Power Unit Wiring Locator

    POWER UNIT WIRING LOCATOR REFERENCE POWER UNIT WIRING DIAGRAM FRONT VIEW RIGHT VIEW PAGE 73 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 74: Wiring Diagram Control Box Side

    WIRING DIAGRAM CONTROL BOX SIDE PROPANE POWER UNIT THROTTLE ON/OFF SWITCH LIGHT SWITCH ON/OFF SWITCH CHOKE HOUR METER 16 AWG BLK +12VDC. BUS 16 AWG RED FROM IGN. SW. 16 AWG GREEN GND. BUS LOFA GAUGE 6-PIN REFERENCE GRN/BLK 6-PIN CONTROL BOX WIRING LOCATOR GND.

  • Page 75: Wiring Diagram Power Unit Side

    WIRING DIAGRAM POWER UNIT SIDE K0-1 NC REFERENCE SSVEC SSVEC FUSE FUSE THROTTLE START POWER UNIT SOLENOID SOLENOID K1-1 NO PLUGS REC. LIGHT WIRING LOCATOR COMMON RELAY BLACK BLACK (P11) (J1) LEFT FRONT LIGHT FUSE 30A GND. RED/VIOLET +12VDC GOVERNOR BLUE BLUE (P7)

  • Page 76: Seat/Horn/Drive Solenoid Wiring Locator

    SEAT/HORN/DRIVE SOLENOID WIRING LOCATOR TB21 TB7 - B TB17 - B SOLENOID VALVE PAGE 76 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 77: Seat/Horn/Drive Solenoid Schematic

    SEAT/HORN/DRIVE SOLENOID SCHEMATIC DRIVE SAFETY SOLENOID VALVE SEAT SWITCH BLACK +12VDC BLACK HORN BUTTON HORN +12VDC RED SPLICE GND. BLK GND. CONTROL BOX SIDE +12VDC GND. TB17 PAGE 77 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 78: Igniter Locator

    IGNITER LOCATOR IGNITION COILS ROLLER SCREED IGNITER PAGE 78 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)

  • Page 79: Igniter Wiring Diagram

    IGNITER WIRING DIAGRAM COLOR OF WIRING B... Black BY ..Black / Yellow BW ..Green / White LW ..Blue / White R ..Red Y ..Yellow BOr..Black / Orange Br ..Brown Gr ..Gray Or ..Orange RB ..

  • Page 80: Power And Ground Connections

    POWER AND GROUND CONNECTIONS GREEN EMERGENCY FUSE STOP SWITCH (PU SIDE) +12VDC OUTPUT +12VDC SPLICE POS. FROM IGN. NEG . TO ALT F U S E 20 AMP B O X FUSE ENGINE NON SWITCHED GROUND 60 AMP POWER FUSE SWITCHED RELAY MODULE...
  • Page 81 NOTES PAGE 81 — WRS5200DFPU HYDRAULIC ROLLER SCREED • OPERATION MANUAL — REV. #2 (03/08/18)
  • Page 82 © COPYRIGHT 2018, MULTIQUIP INC. Multiquip Inc , the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property of their respective owners and used with permission.

This manual is also suitable for:

Wrs5200dfpu

Table of Contents