Install Electrical Kits; Install (Fixed / Wired) Awning Switch; Install Track And Light Switches (If Applicable); Install Ignition / Safety Interlock System - Dometic 9100 Installaiton Instructions

INSTALL ELECTRICAL KITS

 ELECTRICAL SHOCK HAZARD.
Disconnect 120 Vac power from RV. Failure to obey
this warning could result in death or serious injury.
 Disconnect the positive (+) 12 Vdc
terminal from supply battery. Otherwise, damage to
unit could occur.
Disconnect power for ALL procedures under this
section.
A.

Install (Fixed / Wired) Awning Switch

 U se correct (Dometic Corporation approved)
momentary switch, or electronic control
switch with motor overload protection.
1.   Do NOT expose switch to weath-
er, extreme temperatures, or long hours in direct
sunlight.
Find a suitable location for awning switch instal-
lation.
2.  Install a (15 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc power
supply ( RED wire) to switch. Otherwise, damage
to unit could occur.
3. Route wiring (inside RV) to general location
where connections to awning right hand hard-
ware will be made.
 A llow enough wiring length to pass through
outside RV wall (hole will be drilled later)
for connection to awning.
Wiring hole location will be either at top or
bottom of RH back channel depending on
awning model. See (FIG. 1).
4. Make appropriate wiring connections inside RV.
 W iring connections to awning (through
outside RV wall) will be made later.
See instructions included with your Do-
metic Corporation switch kit (available
separately) for additional wiring instruc-
tions.
B. Install Track And Light Switches (If
Applicable)
 U se correct (Dometic Corporation approved)
non-momentary switch.
1.   Do NOT expose switch to weath-
er, extreme temperatures, or long hours in direct
sunlight.
Find a suitable location for awning switch instal-
lation.
2.  Install a (15 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc power
supply ( RED wire) to switch. Otherwise, damage
to unit could occur.
3. Route wiring (inside RV) to general location
where connections to awning left hand hardware
will be made.
 A llow enough wiring length to pass through
outside RV wall (hole will be drilled later)
for connection to awning.
Wiring hole location will be either at top or
bottom of LH back channel depending on
awning model. See (FIG. 1).
4. Make appropriate wiring connections inside RV.
 W iring connections to awning (through
outside RV wall) will be made later.
See instructions included with your Do-
metic Corporation switch kit for additional
wiring instructions.
C.

Install Ignition / Safety Interlock System

 IMPACT OR CRUSH HAZARD. Do
NOT install product without also installing an igni-
tion/safety interlock system. Otherwise, accidental
operation during transit could occur. Failure to obey
this warning could result in death or serious injury.
 I gnition / safety interlock system is only ap-
plicable to motorhomes.
1.   Install a (3 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc igni-
tion control ( PINK wire) to ignition interlock. Oth-
erwise, damage to unit could occur.
2. Make appropriate wiring connections.
 T he ignition interlock MUST break the cir-
cuit (cut power) to awning when ignition
is ON.
See instructions included with your Do-
metic Corporation ignition interlock kit
(available separately) for additional wiring
instructions.
D.

Install LED Light Switch (If Applicable)

An LED light switch (installer supplied) is required
for awning models equipped with an LED light strip
either at the wall or in the roller tube.
 S kip this subsection if awning is NOT
equipped with an LED light strip.
1.   Do NOT expose switch to weath-
er, extreme temperatures, or long hours in direct
sunlight.
Find a suitable location for LED switch installa-
tion.
2.  Install a (3 A) fuse (installer sup-
plied) at fuse panel for positive (+) 12 Vdc power
supply ( RED wire) to switch. Otherwise, damage
to unit could occur.
8