Control Change - Roland RD-700 Owner's Manual

❍Data set 1DT1
This is the message that actually performs data transmission, and is used when you wish to
transmit the data.
Status Data byte
F0H 41H, dev, 00H, 43H, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 00H - 1FH, 7FH, Initial value is 10H)
00H Model ID #1 (RD-700)
43H Model ID #2 (RD-700)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the data to be sent
bbH Address: upper middle byte of the starting address of the data to be
sent
ccH Address: lower middle byte of the starting address of the data to be
sent
ddH Address LSB: lower byte of the starting address of the data to be sent.
eeH Data: the actual data to be sent. Multiple bytes of data are transmitted
in order starting from the address.
: :
ffH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in "Parameter Address Map" (p. 153).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to (p. 160)
* Not Received when the GM Mode is ON.
❍Data set 1DT1 (GM Mode)
Status Data byte
F0H 41H, dev, 42H, 12H, aaH, bbH, ccH,
ddH, ... eeH, sum
Byte Explanation
F0H Exclusive status
41H ID number (Roland)
dev Device ID (dev: 10H)
42H Model ID (GS)
12H Command ID (DT1)
aaH Address MSB: upper byte of the starting address of the transmitted
data
bbH Address: middle byte of the starting address of the transmitted data
ccH Address LSB: lower byte of the starting address of the transmitted
data
ddH Data: the actual data to be transmitted. Multiple bytes of data are
transmitted starting from the address.
: :
eeH Data
sum Checksum
F7H EOX (End Of Exclusive)
* The amount of data that can be transmitted at one time depends on the type of data, and
data will be transmitted from the specified starting address and size. Refer to the address
and size given in "Parameter Address Map" (p. 153).
* Data larger than 256 bytes will be divided into packets of 256 bytes or less, and each
packet will be sent at an interval of about 20 ms.
* Regarding the checksum, please refer to (p. 160)
* Not Received when the GM Mode is OFF.
2. Data Transmission
■Channel Voice Messages
Status
●Note off
F7H
Status
8nH
n = MIDI channel number:
kk = note number:
* Note off message is sent out with the velocity of 40H.
●Note on
Status
9nH
n = MIDI channel number:
kk = note number:
vv = note on velocity:
●Control Change
* By selecting a controller number that corresponds to the setting of parameters of
controllers (Control Src, Foot Controller Assign), the RD-700 can transmit any control
change message.
* These messages are not transmitted when MIDI Tx Parameter is OFF.
❍Bank Select (Controller number 0, 32)
Status
BnH
BnH
n = MIDI channel number:
mm, ll = Bank number:
* When Rec Mode is ON (EDIT:Utility:Rec Setting:Rec Mode), these messages are
transmitted when Tone is selected.
* These messages are transmitted when Bank Select parameter is Set on MIDI Tx Part.
* The Bank Select Numbers corresponding to SRX series should be referred to the SRX
Status
series owner's manual.
F7H
❍Modulation (Controller number 1)
Status
BnH
n = MIDI channel number:
vv = Modulation depth:
* These messages are transmitted when Modulation lever is operated.
❍Portamento Time (Controller number 5)
Status
BnH
n = MIDI channel number:
vv = Portamento Time:
* These messages are transmitted when Portament Time is set in MIDI Tx Mode.
❍Data Entry (Controller number 6, 38)
Status
BnH
BnH
n = MIDI channel number: 0H - FH (ch.1 - 16)
mm, ll = the value of the parameter specified by RPN/NRPN
mm = MSB, ll = LSB
* These messages are transmitted when Bend Range value is set in MIDI Tx Mode.
❍Volume (Controller number 7)
Status
BnH
n = MIDI channel number:
vv = Volume:
* These messages are transmitted when PART VOLUME Slider is operated.
MIDI Implementation
2nd byte 3rd byte
kkH 40H
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
2nd byte 3rd byte
kkH vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
01H - 7FH (1 - 127)
2nd byte 3rd byte
00H mmH
20H llH
0H - FH (ch.1 - 16)
00 00H - 7F 7FH (bank.1 - bank.16384)
2nd byte 3rd byte
01H vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
2nd byte 3rd byte
05H vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
2nd byte 3rd byte
06H mmH
26H llH
2nd byte 3rd byte
07H vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
151