Table of Contents
Advertisement
Problem
In some cases where the delay timing
selected in the DELAY settings in
MFX/Reverb/Chorus is set to a note
value, the delay sound may not be
heard. Either adjust the tempo or
change the numerical value of the de-
Effects Not Ap-
lay timing (p. 79).
plied/Effects
Check the MFX Source and MFX Dest
Sound Wrong
settings for multi-effect that is not
sounding in the Lower Part to which
it is applied (p. 77).
• With certain settings, the Lower
Part's MFX settings are disregard-
ed.
Is the Tone Wheel screen appearing
in the display?
No Pitch Bend
• The pitch bend effect cannot be ap-
When Pitch
plied with the pitch bend lever
Bend Lever is
while the Tone Wheel screen is in
the display. In this case, the pitch
Moved
bend lever functions as a slow/fast
switch for the Rotary effect (p. 75).
Sounds Come
In some Tones, the settings are such
From Left or
that sounds randomly play from the
Right Each Time
left or right side (are panned) each
time the keys are pressed. These set-
Key is Pressed
tings cannot be changed.
(Panned)
Sounds can be distorted due to
equalizer, multi-effect, and Part vol-
ume settings. Adjust the following
settings.
• PART LEVEL sliders (p. 45).
• Edit mode MFX/Reverb/Chorus
Sound is Distort-
MFX <Other Prm> effect levels (p.
ed
77).
• System Master Volume settings (p.
70).
Is a distortion-type effect being ap-
plied to the sound (p. 77, p. 80)?
The screen is displayed by selecting a
Cannot Select
Organ Tone (Tone Wheel 1~10) for
the Draw Bar
any of the UPPER1, UPPER2, or
Screen (Tone
LOWER Parts in the Tone screen, and
Wheel Screen)
then pressing CURSOR [ ] (p. 75).
Key Range Set-
Is [SPLIT] set to OFF?
tings Not Effec-
• Key Range goes into effect when
[SPLIT] set to ON (p. 63, p. 88).
tive
Check/Solution
Problem
Is the System Clock Source setting in
Edit mode set to MIDI?
Tempo Doesn't
• When you want to perform using
Change
the RD-700's tempo, set this to
"INT" (p. 70).
Depending on the Tone selected,
pitches played in certain registers
will be changed and played at other
pitches.
Is Coarse Tune, Fine Tune, or Stretch
Tune set for any specific Part?
• Check the Tone Edit Course Tune,
Fine Tune and Stretch Tune set-
tings in Edit mode (p. 80, p. 81), or
Pitch is Odd
C.T and F.T setting in MIDI TX
screen.(p. 65).
Has the RD-700 gone out of tune?
Check the System Master Tune set-
tings in Edit mode (p. 29).
Has the pitch been changed by pedal
operations or by Pitch Bend messag-
es received from an external MIDI
device?
When you try playing more than the
maximum 128 voices simultaneous-
ly, sounds currently being played
Sound is Cut Off
may be cut out.
• Increase the Voice Reserve settings
for the Parts you do not want to
have cut off (p. 90).
Sound Keeps
Is the hold pedal polarity reversed?
Playing When
• Check the System Pedal Polarity
settings in Edit mode (p. 71).
Key is Pressed
Is the Device ID number of the trans-
mitting device matched to the RD-
700's Device ID number?
Exclusive Mes-
• Check the System Device ID set-
sages Cannot
tings in Edit mode (p. 71).
Be Received
Is the RD-700 set to GM mode?
• Press ONE TOUCH [PIANO] or
[SETUP] to exit GM mode (p. 98).
When a Setup name is registered (p.
Setup Name Not
56), names with eight or more of the
Correctly Indi-
letters M, N, or W are not displayed
correctly. Try reducing the number
cated
of these letters.
Troubleshooting
Check/Solution
101
Advertisement
Table of Contents
