Table of Contents
Advertisement
MIDI Implementation
Balance (Controller number 8)
status
2nd byte
BnH
08H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=Balance:
00H - 7FH (0 - 127)
Panpot (Controller number 10)
status
2nd byte
BnH
0AH
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=Panpot:
00H - 40H - 7FH (left - center - right)
* Adjust the stereo location over 128 steps, where 0 is far left, 64 is center, and 127 is far
right. However this is not received when the Pan parameter (PATCH/CONTROL/
RxSWITCH) is OFF.
Expression (Controller number 11)
status
2nd byte
BnH
0BH
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=Expression:
00H - 7FH (0 - 127)
* If the Volume parameter (SYSTEM/CONTROL/CONTROL SOURCE) is set to
VOL&EXP, the volume of the Part corresponding to the MIDI channel of the received
message will be adjusted. However this is not received if the Volume parameter
(PATCH/CONTROL/RxSWITCH) is OFF.
* In GM mode, the volume can always be controlled.
Hold 1 (Controller number 64)
status
2nd byte
BnH
40H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* Not received when the Hold-1 RxSwitch parameter (PATCH/CONTROL/DAMPER) is
OFF.
Portamento (Controller number 65)
status
2nd byte
BnH
41H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
* The Sw parameter (PATCH/CONTROL/PORTAMENTO) will change.
Sostenuto (Controller number 66)
status
2nd byte
BnH
42H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
Soft (Controller number 67)
status
2nd byte
BnH
43H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 7FH (0 - 127) 0-63=OFF, 64-127=ON
Hold 2 (Controller number 69)
status
2nd byte
BnH
45H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 7FH (0 - 127)
* A hold movement isn't done.
Sound Controller 2 (Controller number 71)
status
2nd byte
BnH
47H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The Res parameter (PATCH/TVF/FILTER) will change relatively.
184
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
Sound Controller 3 (Controller number 72)
status
2nd byte
BnH
48H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The T2–4 parameter (PATCH/TVF/TVF ENVELOPE), The T2–4 parameter (PATCH/
TVA/TVA ENVELOPE) will change relatively.
Sound Controller 4 (Controller number 73)
status
2nd byte
BnH
49H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The T1 parameter (PATCH/TVF/TVF ENVELOPE), The T1 parameter (PATCH/TVA/
TVA ENVELOPE) will change relatively.
Sound Controller 5 (Controller number 74)
status
2nd byte
BnH
4AH
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-64 - 0 - +63)
* The Cut parameter (PATCH/TVF/FILTER) will change relatively.
General Purpose Controller 5 (Controller number 80)
status
2nd byte
BnH
50H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 1 will change relatively.
General Purpose Controller 6 (Controller number 81)
status
2nd byte
BnH
51H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 2 will change relatively.
General Purpose Controller 7 (Controller number 82)
status
2nd byte
BnH
52H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 3 will change relatively.
General Purpose Controller 8 (Controller number 83)
status
2nd byte
BnH
53H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
vv=control value:
00H - 40H - 7FH (-128 - 0 - +126)
* The L1–3 parameter (PATCH/TVA/TVA ENVELOPE) of Tone 4 will change relatively.
Portamento Control (Controller number 84)
status
2nd byte
BnH
54H
n=MIDI channel number:
0H - FH (ch.1 - ch.16)
kk=source note number:
00H - 7FH (0 - 127)
* A Note On message received immediately after a Portamento control will be sounded
with the pitch changing smoothly from the source note number. If a voice is already
sounding at the same note number as the source note number, that voice will change
pitch to the pitch of the newly received Note On, and continue sounding (i.e., will be
played legato).
* The speed of the pitch change caused by Portamento is determined by the Time
parameter (PATCH/CONTROL/PORTAMENTO) value.
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
kkH
Advertisement
Table of Contents
