System Common Parameters - Roland SH-201 Owner's Manual

Parameter list

SYSTEM COMMON parameters

These are settings that apply to the entire SH-201.
Parameter Value
MASTER LEVEL 0–127
MASTER TUNE 415.30–
466.20 (Hz)
MASTER KEY -24– +24
SHIFT
PATCH OFF, ON
REMAIN
CLOCK PATCH,
SOURCE SYSTEM,
MIDI, USB
SYSTEM 5–300
TEMPO (BPM)
MIDI parameters
Parameter Value
RX/TX CHANNEL 1–16
MIDI-USB THRU OFF, ON
SOFT THRU OFF, ON
RECEIVE SWITCH
PROGRAM OFF, ON
CHANGE
BANK SELECT OFF, ON
68
Explanation
Determines the overall volume of the SH-
201.
Tunes the entire SH-201. Specified in terms
of the frequency of the A4 key.
Shifts the pitch of the entire SH-201 upward
or downward in semitone steps.
If this is "ON," the sound of the currently
sounding patch will be maintained when
you select a different patch.
Selects the synchronization source for the
arpeggiator/recorder tempo.
PATCH: Synchronize to the tempo saved
in each patch (PATCH TEMPO, p. 64).
SYSTEM: Synchronize to the tempo that
is common to the entire SH-201 system
(SYSTEM TEMPO).
MIDI: Synchronize to MIDI messages re-
ceived via the MIDI IN connector.
USB: Synchronize to MIDI messages re-
ceived via the USB connector.
This is the common tempo value used by the
entire SH-201 when the CLOCK SOURCE
parameter (see above) is set to "SYSTEM."
Explanation
Specifies the MIDI channel on which the SH-201 will
transmit and receive MIDI messages.
If this is "ON," MIDI messages received at the MIDI IN
connector will be re-transmitted without change from
the USB connector.
If this is "ON," MIDI messages received at the MIDI IN
connector will be re-transmitted without change from
the MIDI OUT connector.
If this is "ON," the patch number or the patch bank (A–
D) will change when a program change message is re-
ceived.
If this is "ON," the patch group (PRESET/USER) will
change when a MIDI bank select message is received.
Panel operation
–
Hold down the CANCEL button and turn the PITCH knob
–
1. Hold down the CANCEL button and press the TAP button
2. Press the PRESET button and then press the BANK D button
3. Press the NUMBER 1 button
Lit: ON, Dark: OFF
4. Press the CANCEL button
1. Hold down the CANCEL button and press the TAP button
2. Press the PRESET button and then press the BANK B button
3. Press a NUMBER button (1–4)
1: PATCH, 2: SYSTEM, 3: MIDI, 4: USB
4. Press the CANCEL button
* Don't set this to "MIDI" or "USB" unless you need to syn-
chronize the SH-201 to the MIDI clock from an external de-
vice. With these settings, the arpeggiator, recorder, tempo-
synchronized LFO, etc., will not work correctly.
With the CLOCK SOURCE parameter set to "SYSTEM," press
the TEMPO buttons or press the TAP button three or more
times at quarter-note intervals of the desired tempo (p. 22, p.
26).
Panel operation
1. Hold down the CANCEL button and
press the TAP button
2. Press the PRESET button and then press
the BANK A button
3. Press a NUMBER button (1–8)
1–8 (Lit in red): 1–8
1–8 (Lit in green): 9–16
4. Press the CANCEL button
1. Hold down the CANCEL button and
press the TAP button
2. Press the PRESET button and then press
the BANK C button
3. Press a NUMBER button (1, 2)
1: MIDI-USB THRU
2: SOFT THRU
Lit: ON, Dark: OFF
4. Press the CANCEL button
1. Hold down the CANCEL button and
press the TAP button
2. Press the PRESET button and then press
the BANK C button
3. Press a NUMBER button (3, 4)
3: PROGRAM CHANGE
4: BANK SELECT
Lit: ON, Dark: OFF
4. Press the CANCEL button