Parameter List; Osc Mix/Mod Parameters - Roland SH-201 Owner's Manual

Parameter list

Here's a list of all the SH-201's parameters.
The right column of the list (the panel operation column) shows how to set parameters that are accessible from
the panel of the SH-201 itself.
You can use SH-201 Editor (p. 56) when you want to create sounds in greater detail, or to create your own
original arpeggios.
* The values listed are the ones that appear in the screen of SH-201 Editor.

OSC MIX/MOD parameters

Parameter Value
OSC1
WAVEFORM SAW, SQR, PW-SQR,
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN
PITCH WIDE OFF, ON
PITCH -36– +36
DETUNE -50– +50
PW/FEEDBACK 0–127
OSC2
WAVEFORM SAW, SQR, PW-SQR,
TRI, SIN, NOISE,
FB-OSC, SUPER-SAW,
EXT-IN
PITCH WIDE OFF, ON
PITCH -36– +36
DETUNE -50– +50
PW/FEEDBACK 0–127
PITCH ENV
A 0–127
D 0–127
OSC1 DEPTH -63– +63
OSC2 DEPTH -63– +63
MIX/MOD
MIX/MOD MIX, SYNC, RING
TYPE
BALANCE -63– +63
LOW FREQ CUT, FLAT, BOOST
60
Explanation
Selects the waveform that is the basis of the sound.
Expands the range of the PITCH knob by three times.
Adjusts the pitch in semitone steps.
Adjusts the pitch in one-cent steps.
• When WAVEFORM is "PW-SQR"
Specifies the width of the upper portion of the square
wave.
• When WAVEFORM is "FB-OSC"
Specifies the amount of output sound that is returned
(fed back) to the input.
• When WAVEFORM is "SUPER-SAW"
specifies the amount of pitch spread between the sev-
en sawtooth waves layered within a single oscillator.
Selects the waveform that is the basis of the sound.
Expands the range of the PITCH knob by three times.
Adjusts the pitch in semitone steps.
Adjusts the pitch in one-cent steps.
• When WAVEFORM is "PW-SQR"
Specifies the width of the upper portion of the square
wave.
• When WAVEFORM is "FB-OSC"
Specifies the amount of output sound that is returned
(fed back) to the input.
• When WAVEFORM is "SUPER-SAW"
specifies the amount of pitch spread between the sev-
en sawtooth waves layered within a single oscillator.
Specifies the time from when you play a key until the
pitch reaches the highest (or lowest) point.
Specifies the time from when the pitch reaches its high-
est (or lowest) point until it returns to the pitch of the key
you pressed.
Specifies the direction and amount of the OSC 1's pitch
change.
Specifies the direction and amount of the OSC 2's pitch
change.
Selects how OSC 1 and OSC 2 are to be combined.
Adjusts the volume balance of OSC 1 and OSC 2.
Selects whether the low frequency range will be boosted
or cut.
Panel operation
Press the WAVE buttons (p. 28)
Press the WIDE button (p. 29)
Turn the PITCH knob (p. 29)
Turn the DETUNE knob (p. 29)
Turn the PW/FEEDBACK knob
(p. 30)
Press the WAVE buttons (p. 28)
Press the WIDE button (p. 29)
Turn the PITCH knob (p. 29)
Turn the DETUNE knob (p. 29)
Turn the PW/FEEDBACK knob
(p. 30)
Move the PITCH ENV A slider
(p. 31)
Move the PITCH ENV D slider
(p. 31)
Press the OSC 1 button and then
move the PITCH ENV DEPTH
slider (p. 28, p. 31)
Press the OSC 2 button and then
move the PITCH ENV DEPTH
slider (p. 28, p. 31)
Press the MIX/MOD TYPE but-
ton (p. 32)
Turn the BALANCE knob (p. 33)
Press the LOW FREQ button (p.
33)