Table of Contents
Advertisement
.SP6498 Belt Drive Saw 05/03
Table of Contents
Section
Table of Contents ..............................................2
Safety Instructions For Table Saw ....................3
Safety Signal Words ......................................3
Before Using The Saw ..................................3
When Installing Or Moving The Saw ................4
Before Each Use ...........................................4
(Kickbacks Or Throwbacks) ..........................5
Eyes, Hands, Face and Ears ........................6
Whenever Sawblade Is Spinning ..................7
Additional Safety Instructions For: ................8
Additional Safety Instructions For: ................9
Herc-U-Lift™ Caster System: ........................9
Glossary of Terms for Woodworking ................9
Requirements ...............................................11
General Electrical Connections ...................11
Changing Motor Voltage ..............................13
Motor Thermal Overload Protector .............14
Wire Sizes ....................................................14
Unpacking and Checking Contents ................15
Tools Needed ...............................................15
Unpacking ....................................................15
List of Loose Parts .......................................16
Herc-U-Lift™ Caster Carton ........................17
Loose Parts .................................................17
Assembly .........................................................17
Installing Bevel Handwheel .........................17
Installing Elevation Handwheel ...................18
Assembling Leg Stand ................................18
Mounting Your Saw .....................................19
Assembling Table Extensions ......................21
Checking Table Insert ..................................22
of Sawblade to Miter Gauge Groove ..........23
of Blade to Table ..........................................25
Checking Tilt Mechanism ............................26
Assembly Tips ..............................................27
Upper Assembly ..........................................27
Lower Assembly ..........................................28
to Saw ..........................................................29
Installation Instructions ................................29
Installing Front Rip Fence Guide Bar .........31
Installing Rear Fence Guide Bar .................32
Adjusting Rip Fence Guide Bars .................33
Installing Spacer Bar ...................................34
Rip Fence Alignment Adjustment ................35
Rip Fence Lock Lever Adjustment ..............35
Adjusting Fence Indicator ............................36
Installing Blade Guard .................................36
Aligning Blade Guard ...................................37
7/15/03
7:04 AM
Page 2
Page
Section
Mounting the Motor .....................................38
Installing Belt ...............................................39
Installing Belt Guard ....................................39
Mounting Switch and End Caps ..................40
Securing Electrical Cords ............................41
Installing Guide Bar End Caps ....................41
Getting to Know Your Table Saw ....................42
Using Zero Clearance Insert .......................46
Remove the Existing Insert. .......................47
Operation Tips .............................................48
Before Each Use .........................................49
Throwbacks) ................................................49
Hands, Face and Ears ................................51
Whenever Sawblade Is Spinning ................52
Work Feed Devices ........................................52
Attaching Wood Face Board .......................53
Push Block ...................................................54
Auxiliary Fence ............................................55
Basic Saw Operations ....................................57
Using the Miter Gauge ................................57
for Crosscutting ...........................................57
Crosscutting .................................................57
Repetitive Crosscutting ...............................58
Miter Crosscutting ........................................59
Bevel Crosscutting .......................................59
Compound Crosscutting ..............................59
Using the Rip Fence ....................................60
Ripping .........................................................61
Bevel Ripping Narrow Work ........................62
Using Featherboards for Thru-Sawing ........63
Resawing .....................................................64
Using Carbide Tipped Blades .....................65
Dadoing .......................................................65
Rabbeting ....................................................66
Ploughing and Molding ................................66
Molding ........................................................67
Adjustments ....................................................68
Miter Gauge .................................................68
Maintaining Your Table Saw ...........................69
Maintenance ................................................69
Lubrication ...................................................70
Accessories ..................................................70
Wiring Diagrams ..............................................71
Troubleshooting ..............................................72
General ........................................................72
Motor ............................................................73
Notes ...............................................................75
Repair Parts ....................................................76
2
Page
Hide quick links:
Advertisement
Table of Contents
