Advertisement
Quick Links
Setup Guide — RGB 190FV and RGB 192V
This guide provides quick start instructions for an experienced
installer to set up and operate Extron
RGB 192V analog computer-video interfaces. The
RGB 192V also has audio capabilities.
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the interface as required.
With optional mounting kits, it can be mounted under or through a desk or other furniture.
Step 2 — Connections
N
The drawing below shows an RGB 192V. With the exception of audio features (marked with
an asterisk [*] in the callout), the features described in step 2 apply to both models.
8
2*
C O M P U T E R
AUDIO
I N P U T
POWER
12-15V
1A MAX.
7
a
Computer Input — Connect a computer-video source to this female 15-pin HD connector.
b
Audio input (RGB 192V only) — Connect an unbalanced
stereo audio source to this 3.5 mm mini stereo jack for
unbalanced audio input.
c
Monitor connector — If desired, connect a local monitor or
other device to this female 15-pin HD connector.
d
BNC output connectors — Connect a display to these rear
panel BNC connectors as shown in the figure below.
RGBHV
RGsB
e
Stereo audio output connector (RGB 192V only) — Connect an audio device, such
as powered speakers, to this 3.5 mm, 5-pole captive screw connector for balanced or
unbalanced stereo or mono audio output.
C
For unbalanced audio output, connect the sleeve(s) to the ground contact.
DO NOT connect the sleeve(s) to the negative (-) contacts).
Tip
NO GROUND HERE.
Sleeve(s)
Tip
NO GROUND HERE.
Do not tin the wires!
Unbalanced Stereo Output
RGB 190FV and
®
1
3
9
S E R R
H - S H I F T
S O G
L E V E L
ON
1
2 3 4 5 6
R G B 1 9 2
M O N I TO R
4
Tip (Left) Sleeve (Gnd)
Ring (Right)
RGBS
NOTE
For RGsB video, also select the
SOG option using DIP switch 2 (item
Tip
Ring
Sleeve (s)
Tip
Ring
Balanced Stereo Output
Setup Guide — RGB 190FV and RGB 192V, cont'd
N
Configure the interface for stereo or mono output using rear panel DIP switch 6 in item
DIP switches, below. When Mono is selected, the right and left inputs are combined and
placed on the left output connectors.
f
DIP switches — This bank of DIP switches configures the interface as shown in the
following table. Default position for all switches is off (down).
Switch
1 — Level and peaking
2 — SOG
3 — Serration pulses
4 — DDSP
5 — No monitor
6
6 — Mono audio
D D S P
(spare for RGB 190FV)
N O M O N .
M . AU D I O
g
Power connector — Connect an IEC power cord
between the included 12 V power supply and a
100 VAC/240 VAC, 50-60 Hz source. Connect the power
supply to the interface as shown at right.
C
AUDIO
L/MONO
R
5*
Operation
Tip (Left)
After all devices are powered up, the system is fully operational. If any problems are
Sleeve
(Gnd)
encountered, verify that the cables are routed and connected properly. If your problems
persist, call the Extron S
number shown below.
h
Power indicator —
Amber — Indicates power is applied.
).
6
Green — Indicates that power is applied and a sync signal is present on the input.
i
H(orizontal) Shift — While viewing the displayed image, rotate this control to move
the image to the right or left on the screen.
N
DDSP disables the interface's Horizontal Shift control.
To use the display's centering controls rather than the interface's controls, set the DDSP DIP
switch to On (up).
Extron USA - West
Extron USA - East
Headquarters
+800.633.9876
+800.633.9876
Inside USA / Canada Only
Inside USA / Canada Only
+1.919.863.1794
+1.714.491.1500
+1.919.863.1797 FAX
+1.714.491.1517 FAX
On (up)
0.8 V p-p, 15% peaking
Sync on green (RGsB)
Serration pulses present
Bypass sync processing
No local monitor connected
ID bits 4 and 11 grounded
Mono on left channel only
This product is intended to be supplied by a Listed
Power Unit marked "Class 2" or "LPS", rated
12 VDC, 1.0 A minimum. Always use a power
supply supplied by or specified by Extron. Use of
an unauthorized power supply voids all regulatory
compliance certification and may cause damage to
the supply and the end product. Unless otherwise
stated, the AC/DC adapters are not suitable for use in air handling spaces or in
wall cavities. The installation must always be in accordance with the applicable
provisions of National Electrical Code ANSI/NFPA 70, article 75 and the
Canadian Electrical Code part 1, section 16. The power supply shall not be
permanently fixed to a building structure or similar structure.
Sales & Technical Support Hotline that is closest to you, at the
3
Extron Europe
Extron Asia
Extron Japan
+800.3987.6673
+800.7339.8766
+81.3.3511.7655
+81.3.3511.7656 FAX
Inside Europe Only
Inside Asia Only
+31.33.453.4040
+65.6383.4400
+31.33.453.4050 FAX
+65.6383.4664 FAX
© 2010 Extron Electronics. All rights reserved.
f
,
Off (down)
Unity (0.7 V) p-p, no peaking
RGBHV or RGBS
No serration pulses
Allow sync processing
Local monitor connected
Stereo
Smooth
Ridges
Captive
Screw
A
A
Connector
Tie
Wrap
3"
16 (5 mm)
SECTION A–A
Max.
Power Supply
Output Cord
Extron China
Extron Middle East
+400.883.1568
+971.4.2991800
+971.4.2991880 FAX
Inside China Only
+86.21.3760.1568
68-647-50
+86.21.3760.1566 FAX
Rev. A 03 10
Advertisement
