Tools Commands - Alcatel-Lucent 7710 SR OS Interface Configuration Manual

Tools Commands

aps
Syntax aps aps-id [clear]
aps mc-aps-signaling [clear]
aps mc-aps-ppp [clear]
Context tools>dump>aps
Description This command displays Automated Protection Switching (APS) information.
Parameters
clear — Removes all Automated Protection Switching (APS) operational commands.
mc-aps-signaling — Displays multi-chassis APS signaling information.
mc-aps-ppp — Displays multi-chassis APS PPP information.
Sample Output
*A:AS_SR7_2# tools dump aps aps-33
GrpId = 33, state = Running, mode:cfg/oper = Bi-directional/Bi-directional
Seq
===
000
001
002
003
004
005
7710 SR OS Interface Configuration Guide
revert = 0, workPort: N/A, protPort: 2/1/1, activePort: working
rxK1 = 0x0 (No-Req on Protect), physRxK1 = 0x0, rxK2 = 0x5
txK1 = 0x0 (No-Req on Protect), physTxK1 = 0x0, txK2 = 0x5
K1ReqToBeTxed = 0x0, K1ChanToBeTxed = 0x0, lastRxReq = 0xc
MC-APS Nbr = 100.100.100.1 (Up), advIntvl = 10, hold = 30
workPort: status = OK, Tx-Lais = None, sdCnt = 1, sfCnt = 1
numSwitched = 1, switchSecs = 0, lastSwitched = 07/25/2007 08:00:12
disCntTime = , alarms = , switchCmd = No Cmd
protPort: status = OK, Tx-Lais = None, sdCnt = 1,
numSwitched = 1, switchSecs = 0, lastSwitched = 07/25/2007 08:03:39
disCntTime = , alarms = ,
GrpStatus: OK, mmCnt = 1, cmCnt = 1, psbfCnt = 1, feplfCnt = 2
LocalSwitchCmd: priority = No-Req, portNum = 0
RemoteSwitchCmd: priority = No-Req, portNum = 0
Running Timers = mcAdvIntvl mcHold
processFlag = apsFailures = , sonet = Y
DebugInfo: dmEv = 0, dmClrEv = 0, amEv = 1, amClrEv = 1
cmEv = 1, cmClrEv = 1, psbfEv = 1, psbfClrEv = 1
feplfEv = 2, feplfClrEv = 2, wtrEv = 0, psbfDetectEv = 0
wSdEv = 1, wSfEv = 2, pSdEv = 1, pSfEv = 1
portStatusEv = 8, rxK1Ev = 9, txLaisEv = 2, lastEvName = FeplClr
CtlUpEv = 3, CtlDnEv = 2, wAct = 0, wDeAct = 0
Event TxK1/K2 RxK1/K2
======= ======= ======= =====
ProtAdd 0xc005 0x0000
RxKByte 0xc005 0x6dea
RxKByte 0xc005 0xc005
RxKByte 0xc005 0x2005
pSFClr 0x0005 0x2005
RxKByte 0x0005 0x0005
switchCmd = No Cmd
Dir Active
====== ================
Tx--> Work 497 02:18:10.590
Rx<-- Work 497 02:20:14.820
Rx<-- Work 497 02:21:30.970
Rx<-- Work 497 02:21:36.530
Tx--> Work 497 02:21:40.590
Rx<-- Work 497 02:21:40.600
Interface Configuration
sfCnt = 0
Time
Page 415