Hotpoint FDYF11011K Service Information
  1. Manuals
  2. Brands
  3. Hotpoint Manuals
  4. Dishwasher
  5. FDYF11011K
  6. Service information

Hotpoint FDYF11011K Service Information

Freestanding dishwasher with digit display
Hide thumbs
Table of Contents

Advertisement

Quick Links

Service
Information
© 2015 Reg. Office: Peterborough PE2 9JB Registered in London: 106725
Indesit Company UK Ltd
5407865 Issue 1 Feb. 2015.
SM004058 ~ C00309783
Hotpoint
Freestanding
DISHWASHER
with
Digit Display
using
DEA700 & DEA603
controls
Models Covered:
Model:
FDYF11011G
FDYF11011K
FDYF11011P
Comm
Code
82748
82752
82746

Advertisement

Table of Contents
loading

Related Manuals for Hotpoint FDYF11011K

Summary of Contents for Hotpoint FDYF11011K

  • Page 1 SM004058 ~ C00309783 Hotpoint Freestanding DISHWASHER with Digit Display using DEA700 & DEA603 controls Models Covered: Comm Model: Code FDYF11011G 82748 FDYF11011K 82752 FDYF11011P 82746 Service Information Indesit Company UK Ltd © 2015 Reg. Office: Peterborough PE2 9JB Registered in London: 106725...

  • Page 2: Table Of Contents

    Indesit Company SAFETY NOTES & GENERAL SERVICING ADVICE 1. This manual is NOT intended as a comprehensive repair/maintenance guide to the appliance. 2. It should ONLY be used by suitably qualified persons having technical competence applicable product knowledge and suitable tools and test equipment. 3.

  • Page 3: Product Fiche

    3=Active SB=Gun U=Ultima 5=Flexiload metal Star Product Fiche - FDYF11011 Product Fiche HOTPOINT Brand FDYF 11011 Model Rated capacity in standard place settings (1) 295.0 Energy consumption per year in kWh (2) 1.04 Energy consumption of the standard cleaning cycle in kWh...

  • Page 4: Technical Specifications

    Indesit Company TECHNICAL SPECIFICATIONS Models FDYF11011G 82748 Graphite FDYF11011K 82752 Black FDYF11011P 82746 White First Production 2013 Energy Class Washing Class Drying Class Noise Level 49 dB Country of Origin Poland Dimensions Height - 850 mm Width - 600 mm...
  • Page 5 Indesit Company FAULT CODES - Basic If there is a fault (active): The service technician will find the machine immobilized, with the Fault Code shown in the display and other LEDs on the Control Panel blinking (usually On/Off, Salt and Rinse Aid). Refer to the Fault Code chart below for guidance.
  • Page 6 Indesit Company FAULT CODES - Detailed FAULT NAME POSSIBLE CAUSE CHECKS CODE - Water leak; - Float switch or wiring defective; ANTI-FLOODING Bowl oat microswitch electrical - New main board: Eeprom was programmed OVERFLOW circuit OPEN! (must be closed) off-site; to reset the alarm, switch off and switch on again using the ON/OFF button.
  • Page 7 Indesit Company Thermistor - Resistance Chart Temperature Resistance Temperature Resistance in degrees C in K Ohms in degrees C in K Ohms - 40 24751.661 146.215 - 35 17127.169 117.828 - 30 12014.762 95.420 - 25 8524.305 77.718 - 20 6113.811 63.584 - 15...
  • Page 8 Indesit Company • Programme Times The times in the handbook and displayed at the start of the cycle, are average times and will be affected by the following points: • Inlet water temperature below 19°C • Tab option enabled • Water hardness setting set to positions 4 or 5 •...
  • Page 9 WIRING DIAGRAM DEA700 Module DEA700 Module J 11 J 12 J 14 J 13 Key: Mains power Noise filter Heating element Thermoprotector (95°C) Thermal fuse (206°C) Synchronous drain pump Synchronous washing motor Door microswitch Dispenser solenoid valve Load solenoid valve M Regeneration solenoid valve Pressure switch O Overflow switch...
  • Page 10 WIRING DIAGRAM DEA603 Module DEA603 Module Key: Mains power CN10 CN11 Noise filter Heating element Thermoprotector (95°C) Thermal fuse (206°C) Synchronous drain pump Synchronous washing motor Door microswitch Dispenser solenoid valve Load solenoid valve M Regeneration solenoid valve Pressure switch O Overflow switch Meter turbine Rinse aid reader...

  • Page 11: General Information

    Indesit Company GENERAL INFORMATION These models are freestanding front loading Dishwashers providing a choice of 8 Wash Cycles. They have A+ Energy performance. Programmes and all Options are set using the display, which is mounted on the console. Extra Dry, Tabs, Half Load, Shortime and Delay Options are also available on selected programmes. Smaller loads can be washed using either the top or bottom basket.

  • Page 12: Console Panel

    Indesit Company CONSOLE PANEL Control Panel Delayed Start buttons Multi-functional Tablets Wash-Cycle Selection buttons option button (Tabs) Start/Pause button On-Off/Reset button and indicator lights Display and indicator light Extra Drying option button Half Load option button Wash-Cycle Selection buttons Short Time option button Display Remaining Time indicator Low Salt indicator light...
  • Page 13 Indesit Company START/PAUSE BUTTON Once the Programme and Options required have been selected. Pushing this button once will start the selected Programme. During a Programme if this button is pushed the Cycle will stop until the button is pushed again, when the cycle will continue.
  • Page 14 Indesit Company DELAY START The Cycle start can be delayed for up to 24 hours in 1-hour steps. Select required wash cycle and any options and push the Delay button until the required delay time is displayed. Press the Start/Pause button to begin the delay period. During the delay period, "Start in"...
  • Page 15 Indesit Company BASIC MACHINE USE Note: Water Hardness MUST be set BEFORE first use or after module replacement. Setting a Programme Turn the Machine On (On-Off Button). Start Pause Button Flashes. Push P button until required programme is displayed. Select any required Option. Press the Start Button (lamp will stop flashing and stay permanently on..).
  • Page 16 Indesit Company Service Manual UK English 16 of 39...

  • Page 17: Programme Guide

    Indesit Company PROGRAMME GUIDE - FDYF11011 Wash-cycle data is measured under laboratory conditions according to European Standard EN 50242. Based on the different conditions of use, the wash-cycle duration and data can change. The number and type of wash cycles and options may vary depending on the dishwasher model. Water Energy Wash Cycle...

  • Page 18: Component Description

    Indesit Company COMPONENT DESCRIPTION Module Mounted behind the plinth, this is an electronic device that monitors and controls all devices within the appliance. If replacing this module, refer to the Module Programming section on in this manual. Both DEA700 and DEA603 Modules have been used in Production. The DEA700 Module was used in Production up to Industrial Code ending 2500.
  • Page 19 Indesit Company Consisting of a polystyrene float and microswitch. An excess of water in the base panel operates the float switch sending a signal to the control module operating the drain pump and displaying a fault code on the console. Filling Sequence 1.
  • Page 20 Indesit Company Detergent, Rinse Aid Dispenser The dispenser fitted to these models works differently to dispensers previously found on Hotpoint / Indesit Dishwashers. Dispenser showing flaps closed Dispenser showing flaps opened Release Tablet / Powder Rinse button Detergent Dispenser Operation of Detergent Dispenser: The dispenser incorporates a solenoid valve at the rear which, when activated, opens the dispenser to release the detergent and at the same time releases the rinse aid.
  • Page 21 Indesit Company ADDITIONAL COMPONENTS INFORMATION Aqua-Stop Inlet Valve The Aqua stop inlet water valve is located in the tap end of the fill hose. In the event of a split fill hose or the machine leaking, water will fill the base tray and operate the base float switch, which will Hose signal the module to switch off the inlet...
  • Page 22 Indesit Company Low Salt Warning An Optical Sensor is fitted to the salt container where the presence of salt breaks the beam in the sensor. When the level of salt is below the sensor level, the receiving sensor receives the light beam from the sending LED.
  • Page 23 Indesit Company Service Manual UK English 23 of 39...

  • Page 24: Auto Test Cycle

    Indesit Company AUTO TEST CYCLE Activation of the Auto Test Cycle: 1. Switch ON the appliance 2. Switch OFF the appliance 3. Push P5 (Tri Wash) 4. Push P1 (ECO) 5. Push P5 (Tri Wash) 6. Switch ON the appliance 7.
  • Page 25 Indesit Company If there is a fault (active): The service technician will find the machine immobilized, with the Fault indicator LEDs permanently alight and other LEDs on the Control Panel blinking. Digit and LCD display models will show the Fault Code in the display.

  • Page 26: Dismantling Instructions

    Indesit Company DISMANTLING INSTRUCTIONS SAFETY NOTES:- 1. ENSURE THAT THE MACHINE IS UNPLUGGED BEFORE DISMANTLING 2. BEWARE OF SHARP EDGES ON METAL PANELS AND PRESSED PARTS. Access to all components are via the side panels, front plinth or the access panel in the base tray. Plinth and Side Cheek Assembly Fully open the dishwasher door.

  • Page 27: Module Programming

    Indesit Company Power Module Release front access flap as in E). and release harness retaining clip before hinging down. Slide power module towards connections to release from access panel. Note position and remove connections. Release board from carrier. Note: A Service Module is supplied WITHOUT a programme loaded. Refer to the Module Programming section in this manual.
  • Page 28 Indesit Company H. Circulating Motor & Heater Hose Remove base access panel as in G). Clips Release 2 hose clips and hoses. Ease motor towards front away from mounting bracket. Separate motor from heater by twisting in an anti-clockwise direction. Mounting Important Bracket...
  • Page 29 Indesit Company Air-break & Turbine Facing the front of machine remove l/h side panel as in D). Unscrew the ring nut fixing the air-break to the D/W tank. Disconnect the flow meter wiring. Lift air-break up and release from water softener.
  • Page 30 Indesit Company P. Display Board Remove outer door panel C). Remove console panel (6 screws) and disconnect wiring plugs (2). Note the connector orientation and position. Carefully ease the ribbon cable (connected to the touch control surface) from its socket. The touch control surface is an integral part of the console moulding and is not available separately.
  • Page 31 Indesit Company Door Hinge Remove the front panel and both side panels. Partially open the door (half way). Insert a sturdy pin (or pop rivet etc.) in the hinge hole (in both Left and Right hinges) to keep the door half open.
  • Page 32 Indesit Company R. Inner Door Panel wiring layout Note correct location of wiring harness behind the Tie Rod Service Manual UK English 32 of 39...
  • Page 33 Indesit Company Module Programming The module will always be supplied without a programme when supplied as a spare part. NOTE: This module DOES NOT have a physically replaceable Eeprom. Programming Access Panel - situated beneath the Dishwasher Door. Use a small flat bladed screwdriver to release the panel Programming a Main Board There are a number of ways the board can be programmed - some of which are not applicable to certain markets.
  • Page 34 Indesit Company PROGRAMMING (Using Smartcard Reader / Card). Smart Card Smart this card holds Card the program file Reader and can ONLY be used ONCE. After the module has been programmed the card is automatically erased. If the Main Module has been replaced during a repair the module will require programming using the following method.

  • Page 35: General Dishwashing Information

    Indesit Company GENERAL DISHWASHING INFORMATION NOTE: - Many faults occur over along period of washing incorrectly. Correcting faults may not immediately cure a problem, e.g. several washes may be necessary to give better results. POOR WASH RESULTS A variety of factors influence wash results and some of the more common are listed below. A.
  • Page 36 Indesit Company B. WHITE COATING ON DISHES AND INSIDE THE MACHINE 1. White coating or scale Detergent not only loosens the remains of food but, together with the calcium salts in the water, forms water-soluble compounds which prevent the appearance of the white calcium coating or scale. Insufficient detergent may result in a white coating on dishes and the machine interior.
  • Page 37 Indesit Company E. POOR DRYING 1. Correct amount of Rinse Aid The purpose of rinse aid when added to the water of a final rinse is to allow the water to run off the dishes as a complete film so that no water-run marks or calcium are left. To enable this to happen it is essential that the correct amount of rinse aid is dispensed.
  • Page 38 Indesit Company 2. Nickel Silver (German Silver) is an alloy of copper, nickel and zinc, and when subjected to heat in dishwashing solutions the metal acquires a yellow colour. Maintaining this alloy in attractive condition requires frequent polishing and it should not be washed in a dishwasher. 3.
  • Page 39 Indesit Company Service Manual UK English 39 of 39...

This manual is also suitable for:

Fdyf11011gFdyf11011p

Table of Contents