Danfoss VLT MCD 200 Installation Instructions Manual
Finger guards
Hide thumbs
Also See for VLT MCD 200:
- Installation manual (34 pages) ,
- Installation instructions manual (17 pages) ,
- Installation instructions (5 pages)
Advertisement
Quick Links
Installation Instructions
Finger Guards
®
VLT
Soft Starter MCD 200/MCD 500
1 Product Overview
These instructions provide information about installation of
finger guard kits. The instructions are targeted at users already
®
familiar with the VLT
Soft Starters MCD 500, or VLT
Starters MCD 200/202. Read the instructions before installation
and ensure that instructions for safe installation are observed.
Additional resources
Further manuals and instructions are available for download at
vlt-drives.danfoss.com/Support/Technical-Documentation/.
2 Items Supplied
The finger guard is available in different kits depending on
model and enclosure size. For a list of all available kit part
numbers, refer to chapter 4.5 Packing List.
3 Safety Instructions
Finger guards fit over the soft starter power terminals to
increase IP rating and prevent accidental contact with live
®
terminals.
Compact
ELECTRICAL SHOCK HAZARD
®
VLT
connected to mains voltage.
Models MCD5-0360C ~ MCD5-1600C: The bus bar and heat
sink are live while the unit operates (starts, runs, or stops). If
the soft starter is installed without a main contactor, the bus
bar and heat sink are live whenever mains voltage is
connected. This is also the case when the soft starter is
ready or tripped.
Improper installation of the motor or the soft starter, and
installing or servicing with power connected, can cause
death, serious injury, or equipment failure.
To avoid death, serious injury, or equipment failure:
•
•
•
•
•
Danfoss A/S © 04/2016 All rights reserved.
WARNING
Soft Starters contain dangerous voltages when
Only use qualified electricians for carrying out the
electrical installation.
Disconnect the soft starter from all power sources
before installation or service.
Fit finger guards to all terminals, even if no cable is
connected.
Treat the bus bar and heat sink as live whenever
the unit has mains voltage connected. Also take
this precaution when the soft starter is tripped or
waiting for a command.
Follow the guidelines in these instructions and local
electrical safety codes.
MI17A602
Advertisement
Related Manuals for Danfoss VLT MCD 200
Summary of Contents for Danfoss VLT MCD 200
- Page 1 Also take this precaution when the soft starter is tripped or waiting for a command. • Follow the guidelines in these instructions and local electrical safety codes. Danfoss A/S © 04/2016 All rights reserved. MI17A602...
-
Page 2: Installation
Repeat steps 1–4 for the other set of terminals. Retaining bracket Finger guards Finger guard base chassis Top cover Illustration 4.3 Finger Guard Installation for MCD 500 G3C Enclosure Size Illustration 4.1 Finger Guard Installation for MCD 200 Danfoss A/S © 04/2016 All rights reserved. MI17A602... - Page 3 (not supplied) appropriate for the size of cable used. Fit the finger guard cover over the finger guard base chassis to complete the arrangement. Repeat steps 1–5 for the other set of terminals. MI17A602 Danfoss A/S © 04/2016 All rights reserved.
- Page 4 853 (33.6) 1036 (40.8) B [mm (in)] – – – 300 (11.8) 261 (10.3) 308 (12.1) 286 (11.3) C [mm (in)] – – – – – 1146 (45.1) 1319 (51.9) Illustration 4.8 Dimensions Danfoss A/S © 04/2016 All rights reserved. MI17A602...
-
Page 5: Packing List
1) Only 1 kit required. 2) Each kit is only sufficient for protection of either top or bottom cable terminals. If both top and bottom cable termination is used, 2 finger guard kits are required. MI17A602 Danfoss A/S © 04/2016 All rights reserved. - Page 6 Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice. This also applies to products already on order provided that such alterations can be made without subsequential changes being necessary in specifications already agreed. All trademarks in this material are property of the respective companies. Danfoss and the Danfoss logotype are trademarks of Danfoss A/S.