Advertisement
MOUNTING THE PHONE
Wall Mounting
(With or Without a Wall Plate)
The mounting bracket comes attached to the lower base
of the phone for immediate wall mounting.
Adjust the handset holder
by sliding the clip up. Then
rotate it and slide it back
into the slot.
To mount the phone on a
wall plate , connect the supplied short cord to the phone's
line jack and route it through the groove on the base.
To mount the phone without a wall plate , connect the sup-
plied long cord. Then use two
3
/
-inch (5 mm) screws (not
16
supplied) to mount the phone on the wall.
Mounting without a Wall Plate
Mounting with a Wall Plate
Desktop Mounting
To place the phone on a flat surface, remove the mounting
bracket by sliding the bracket to the right and then away
from the phone.
Insert the tab on the wide end of the bracket into the
base's upper left slot, and the other tab into the base's
upper right slot. Then slide the bracket to the right to snap
the bracket into place.
Note: The phone company can charge you for the instal-
lation of the necessary jacks. The USOC number of the
jack to be installed is RJ11C (RJ11W for a wall jack).
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol is intended to alert you
that parts inside the telephone present
a risk of electric shock.
This symbol is intended to alert you to
important
operating
instructions included in the papers with
the telephone.
USING THE PHONE
Press
REDIAL
number dialed (up to 31 digits).
Press
FLASH
for special services, like Call Waiting.
Note: If you do not subscribe to any special
services, pressing
the call.
To make or answer a call using a headset, press
HEADSET
phone number. To end a call, press
STORING/DIALING NUMBERS IN MEMORY
You can store up to 13 numbers (three priority –
, and 10 standard – one for each number key).
M3
To store a number (up to 16 digits) in memory:
1. Lift the handset. If you wear a headset, press
HEADSET
2. Enter the telephone number you want to store.
Then press
3. To store a number in a priority memory, press
M2
number (
store the number.
4. To store more numbers, repeat Steps 1–3.
and
servicing
Lift out the memory
index card and
record important
phone numbers.
Plug the handset cord
into the jacks on the
handset and base.
to dial the last
for a timed switchhook signal
FLASH
might disconnect
. Then (if you are making a call), dial the
HEADSET
. Then press
.
STORE
.
STORE
, or
. For standard memories, enter the 1-digit
M3
–
) for the location where you want to
0
9
RadioShack is a registered trademark used by Tandy Corporation.
MEMORY
,
STORE
, and
See "Storing/Dialing Numbers in Memory."
Press to
disconnect
a call.
Set
VOLUME LOW
to adjust the volume you hear
through the handset.
The headset indicator
lights when you make
and
receive
a
call
using a headset, and
turns off when you end
again.
a call.
To dial a number in a priority memory:
,
,
M1
M2
1. Lift the handset. If you wear a headset, press
.
HEADSET
2. Press the priority button (
number you want to call.
To dial a number in standard memory:
1. Lift the handset.
M1
,
2. Press
.
MEMORY
3. Enter the 1-digit location number for the number
you want to call.
1999 Tandy Corporation.
All Rights Reserved.
M1
,
M2
, and
M3
—
If you have pulse service,
press
to dial num-
*
/TONE
bers as tone signals. The
phone returns to pulse dial-
ing when you hang up.
Set to
or
TONE
PULSE
according to the type
of service you have.
Set the
RINGER
to
OFF
,
LOW
or
Set the
HIGH
. You can make calls with
RINGER
to
OFF
,
LOW
or
the ringer off, and you can
. You can make calls with
HIGH
receive calls if you hear another
the ringer off, and you can
phone on the same line ringing.
receive calls if you hear another
/
/
MED
HIGH
The headset jack ( )lets you con-
nect an optional headset, so you
can step away within the cord's
reach to do another job (available
from RadioShack).
To connect a headset, insert the
headset's
/
-inch (2.5-mm) plug
3
32
into
.
,
, or
) for the
M1
M2
M3
Advertisement
