Using The Attenuator; Turning The Key Tone On And Off; Changing The Display Contrast; Cloning Programmed Data - Radio Shack PRO-2053 Owner's Manual

To change the receive mode, repeatedly
press . The receive mode changes as
MODE
follows:
— accesses the AM mode
ã) ã)
ã) ã)
— accesses the FM mode
") ")
") ")
— accesses the FM Mode, Motorola
)+ )+
)+ )+
Trunking System (with a 4- or 5-digit ID
code)
— accesses the FM Mode, EDACS
! ! ! !
Trunking System (with 4-digit decimal ID
code or 5-digit AFS code)
Note: MO (MOT) and ED modes are not
available when the scanner tunes up or
down through the frequency ranges in which
the trunking operation is not used.

USING THE ATTENUATOR

To reduce interference or noise caused by
strong signals, you can reduce the scanner's
sensitivity to these signals.
There are two attenuator modes in your
scanner. In normal attenuator mode, you set
the attenuator in each channel or each band/
group in the search and tune mode. In global
mode, you set the attenuator only once. The
global setting affects every mode.
Press to turn on or off the attenuator
ATT
while the channel number is indicated, or
while the scanner is searching through
bands/groups. When the attenuator is on,
appears at the seventh digit in the top line.
When you turn it off,
cannot set the attenuator while the scanner
is scanning.
Press then
FUNC ATT
the global mode.
#CF98Cý ã00ô #CF98Cý ã00ô #CF98Cý ã00ô #CF98Cý ã00ô
seconds at the bottom line and
(off) appears. Press
attenuator.
ã00FE ã00FE
ã00FE ã00FE
bottom line while scanning.
ô ô ô ô
changes to "
ã ã ã ã
to set the attenuator to
appears for 2
Wý Wý Wý Wý
(on) or
to turn on or off the
ATT
or appears on the
ã00Vý ã00V
ã00V ã00V
Press
FUNC
global attenuation mode.
cated at the bottom line for 2 seconds.
Note: If you turn on the attenuator, the scan-
ner might not receive weak signals.
TURNING THE KEY TONE ON
AND OFF
Each time you press any of the scanner's
keys, the scanner sounds a tone. To turn the
scanner's key tone off or on:
1. If the scanner is on, turn
MAX
turn the scanner off.
2. Turn
turn the scanner on.
0ILEB@E> 0ILEB@E>
0ILEB@E> 0ILEB@E>
3. While
appears, press
or
2
CHANGING THE DISPLAY
CONTRAST
1. Press
2. Press
KFýJ<Ký:FEKI8JKô KFýJ<Ký:FEKI8JKô KFýJ<Ký:FEKI8JKô KFýJ<Ký:FEKI8JKô
3. Press
4. Press
ã ã ã ã
CLONING PROGRAMMED
DATA
". You
You can transfer programmed data to and
from another RadioShack PRO-2053 or a
PRO-93 scanner using an optional connect-
ing cable with
ends, (not included) available at your local
# # # #
RadioShack store.
Follow these steps to clone the data.
Special Features
then again to turn off the
ATT
*FID8Cý ã00 *FID8Cý ã00
*FID8Cý ã00 *FID8Cý ã00
counterclockwise until it clicks to
VOLUME OFF/MAX
3<C:FD<ý 0Fý 3<C:FD<ý 0Fý 3<C:FD<ý 0Fý 3<C:FD<ý 0Fý
appears.
3<C:FD<ý 3<C:FD<ý 0Fý 0Fý
3<C:FD<ý 3<C:FD<ý 0Fý 0Fý
to turn on the key tone
1
to turn it off.
.
MAN
then .
FUNC 9 1J<ý 1Gó FNEý B<PJ 1J<ý 1Gó FNEý B<PJ
1J<ý 1Gó FNEý B<PJ 1J<ý 1Gó FNEý B<PJ
appears.
8 8 8 8 9 9 9 9
or to select the contrast.
to set the display contrast.
ENTER
1 / -inch phone plugs on both
8
is indi-
VOLUME OFF/
clockwise to
L8C L8C L8C L8C
L8Cý L8Cý 0ILEB@E> 0ILEB@E>
L8Cý L8Cý 0ILEB@E> 0ILEB@E>
29