Certifications; Appendix; P2R Receiver Mix In Jack Wiring Diagrams - Shure PSM 200 User Manual

Certifications

P2T: Certified to FCC Part 74 (FCC ID No. DD4P2T). Certified in Can-
ada by IC to RSS–123 and RSS–102 (Certification No. 616A–P2T).
This class B digital apparatus complies with Canadian ICES–003.
EP2T/UKP2T: Meets essential requirements of European R&TTE Di-
rective 99/5/EC, eligible to bear the CE mark:
proved to EN 300 422 Parts 1 and 2. Meets requirements of EMC Stan-
dard EN 301 489 Parts 1 and 9.
P2R: Approved under the Declaration of Conformity (DoC) provision of
FCC Part 15. Certified in Canada by IC to RSS-123 (Certification No.
616A–P2R). This class B digital apparatus complies with Canadian
ICES–003. Meets essential requirements of European Union R&TTE
Directive 99/5/EC, eligible to bear
EMC standards EN 300 422 Parts 1 and 2 and EN 301 489 Parts 1
and 9.
LIMITED ONE-YEAR WARRANTY
Shure Incorporated ("Shure") hereby warrants that this product
will be free from defects in materials and workmanship for a pe-
riod of one year from the date of purchase for all cartridge and
housing assembly parts and for a period of one year from the
date of purchase for all transmitter parts. At its option Shure will
repair or replace the defective product and promptly return it to
you, or refund the purchase price. You should retain proof of
purchase to validate the purchase date and return it with any
warranty claim.
If you believe this product is defective within the warranty peri-
od, carefully repack the unit, insure it, and return it postage pre-
paid to:
Shure Incorporated
Attention: Service Department
222 Hartrey Avenue
Evanston, Illinois 60202-3696 U.S.A.

APPENDIX

P2R Receiver MIX IN Jack Wiring Diagrams

Mono Line Input
The MIX–IN jack accepts line-level signals, such
as click tracks, effects processors, pre-amp out-
puts from guitar or bass amps, or line outputs from
mixing consoles. When used with a mono connec-
tor, the ring of the MIX IN jack is grounded. This
doesn't harm the P2R.
Condensor Mic TRS Input
By connecting a condensor microphone to the MIX
IN jack, you can include sounds from your immedi-
ate surroundings in your personal mix. When the
MIX IN Jack is used with a TRS connector, such as
the Shure AP200 adaptor, the P2R supplies a 5 volt
bias on the ring signal. This enables the MIX IN jack
to power a condensor microphone. The AP200
works with any Shure microphone that has a mini
4-pin connector.
ENGLISH
O682
. Type ap-
mark. Meets requirements of
14
PS20: Conforms to Safety Standards UL1310 and Canada/CSA22.2,
No. 223
PS20E: Conforms to Safety Standard EN 60065.
PS20UK: Conforms to Safety Standard EN 60065 and BS 7002.
SHURE
P2R
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
Outside the United States, return the product to your dealer or
Authorized Service Center.
This warranty does not apply in cases of abuse or misuse of the
product, use contrary to Shure's instruction, or unauthorized re-
pair. All implied WARRANTIES OF MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE are hereby dis-
claimed and Shure hereby disclaims liability for incidental, spe-
cial, or consequential damages resulting from the use or un-
availability of this product.
Some states do not allow limitations on how long an implied
warranty lasts, or the exclusion or limitation of incidental or con-
sequential damages, so the above limitation may not apply to
you. This warranty gives you specific legal rights, and you may
have other rights which vary from state to state.
THIS WARRANTY SUPERSEDES ALL WARRANTIES THAT
ARE INCLUDED WITH THIS PRODUCT
SLEEVE RING
TIP
SLEEVE RING
TIP
5 V BIAS
PRE–AMP
1 MEG OHM
5 V BIAS
PRE–AMP
1 MEG OHM