Manual Setting Of The Seat Angle On The Groove; Powered Seat Tilt; Preparing Your Seat Position For Driving On The Road - Sunrise Medical Wheelchair Directions For Use Manual

Actuator number. Then operate the Joystick in the forward or rear-
ward direction to move the Legrest up or down. Release the Joy-
stick when the desired angle is reached. Once the legrest is fully
lifted or in its lowest position do not hold the Joystick in its operat-
ing position as this could damage the actuator. To return to Drive
Mode, simply press the Mode Button again.
Note: Both legrests can also be operated simultaneously.
Delphi QR Control:
To operate the legrest simply push the Mode Button twice to
select Actuator Mode. Selection is indicated via the lighting of the
Green LED adjacent to the Mode Button. The wheelchair icon
LEDs in the centre of the Remote, will light up with the currently
selected Actuator Option. Move the Joystick in the left or the right
direction to scroll through the possible options until the legrest
Option is selected. Operate the Joystick in the forward or rearward
direction to move the legrest up or down. Release the Joystick
when the desired angle is reached. Once the Legrest is fully lifted
or in the lowest position do not hold the Joystick in its operating
position as this could damage the actuator. To return to Drive
Mode, simply press the Mode Button.
Note: Both legrests can also be operated simultaneously

5.5. Manual setting of the seat angle on the GROOVE

To set the seat angle, release the bolt fixing the "Banana" bracket
between the Seat Interface Module and the Seat Packer Module.
Set the seat angle at 0°, 3° or 6° and 9°. Then replace and re-
tighten the bolt between the Seat Interface Module and the Seat
Packer Module. (Fig. 44).

5.6. Powered Seat tilt

The seat can tilt up to 30° by operating it through your control
system.
Delphi QC Control:
To operate the Powered Tilt simply push the Mode Button to select
Actuator mode and then operate the Joystick left or right to select
the Actuator required (Actuator 1 or Actuator 2). Selection is indi-
cated via the lighting of the Green LED adjacent to the desired
Actuator number. Then operate the Joystick in the forward or rear-
ward direction to move the Tilt forward or backward. Release the
Joystick when the desired angle is reached. Once the seat is fully
tilted or in its lowest position do not hold the Joystick in its operat-
ing position as this could damage the actuator. To return to Drive
Mode, simply press the Mode Button again.
Delphi QR Control:
To operate the Powered Tilt simply push the Mode Button twice to
select Actuator Mode. Selection is indicated via the lighting of the
Green LED adjacent to the Mode Button. The wheelchair icon
LEDs in the Centre of the Remote will light up with the currently
selected Actuator Option. Move the joystick in the left or the right
direction to scroll through the possible options until the Tilt Option
is selected (Both Seat and Backrest lights lit). Then operate the
Joystick in the forward or rearward direction to move the Tilt for-
ward or backward. Release the Joystick when the desired angle is
reached. Once the Seat is fully tilted or in the lowest position do
not hold the Joystick in its operating position as this could damage
the actuator. To return to Drive Mode, simply press the Mode But-
ton.

5.7 Preparing your seat position for driving on the road

Please ensure your backrest recline angle relative to floor level,
which is a combination of the back recline itself and the tilt angle,
does not exceed 12° to drive the chair safety. If your backrest to
level floor angle exceeds this limit the chair will automatically con-
vert into "creep mode" which will allow you a maximum of 10% of
the speed programmed in the profile.
Operating the powered lift higher than 5cm from its lowest position
will bring the chair into "creep mode", moving it below will allow
full speed.
0705/1/ST-000690620.EMS
Fig. 44
0°
3°
6°
9°
11
GROOVE