Powered Adjustable Backrest; Jay Backrests; Headrest; Powered Lift - Sunrise Medical Wheelchair Directions For Use Manual

6.9.2. Powered adjustable backrest

For depth adjustment see 'Changing the seat depth' above in
section 6.3.
Delphi QC Control:
To recline the backrest angle simp-
ly push the Mode Button to select
Actuator mode (Fig. 55) and then
operate the Joystick left or right to
select the Actuator required
(Actuator 1 or Actuator 2). Selec-
tion is indicated via the lighting of
the Green LED adjacent to the
desired Actuator number. Operate
the Joystick in the forward or rear-
ward direction to move the
backrest up or down. Release the
Joystick when the desired angle is
reached. Once the back is fully
reclined or raised do not hold the
Joystick in its operating position as
this could damage the actuator. To
return to Drive Mode, simply press
the Mode Button again.
Delphi QR Control:
To recline the backrest angle simp-
ly push the Mode Button twice to
select Actuator Mode (Fig. 56 and
57). (If only 1 drive profile is enab-
led, then the mode button needs
to be pressed only once). Selection
is indicated via the lighting of the
Green LED adjacent to the Mode
Button. The wheelchair icon LEDs
in the Centre of the Remote will
light up with the currently selected
Actuator Option. Move the Joy-
stick in the left or the right direction to
scroll through the possible options until
the Backrest Option is selected. Operate
the Joystick in the forward or rearward
direction to move the backrest up or
down. Release the Joystick when the
desired angle is reached. Once the back is
fully reclined or raised do not hold the
Joystick in its operating position as this
could damage the actuator. To return to
Drive Mode, simply press the Mode Button.
Lowering the backrest by an angle of
greater than 15° from vertical alters the
balance of your wheelchair.
Never exceed 15° of recline when on any gradient or when driving
your wheelchair.

6.10. JAY backrests

The standard backrest assembly will allow the fitting of a JAY
backrest, which is available as an optional extra.

6.11. Headrest

To fit the headrest, fit the location bracket to the backrest brace,
using the screws and nuts supplied, ensuring that they are fully
tightened.
The headrest height is changed by loosening the adjustment lever,
and sliding the inner vertical tube to the desired position and tigh-
tening the lever mechanism. The headrest to seat depth is adjusted
by loosening the 6mm Allen screws, and moving the hinge to the
desired position, and then tightening the screws securely. To adjust
the headrest angle, loosen the screws at the headrest upholstery,
position the headrest as required and tighten the screws securely.
0705/1/ST-000690620.EMS
Fig. 55
Fig. 56
Fig. 57

6.12. Powered Lift

The seat can lift up to 30 cm by operating it through your control
system.
Delphi QC Control:
To operate the powered lift simply push the Mode Button to select
Actuator mode (Fig. 57) and then operate the Joystick left or right
to select the Actuator required (Actuator 1 or Actuator 2). Selection
is indicated via the lighting of the Green LED adjacent to the desir-
ed Actuator number. Operate the Joystick in the forward or rear-
ward direction to move the lift up or down. Release the Joystick
when the desired angle is reached. Once the lift is fully raised or in
its lowest position do not hold the Joystick in its operating position
as this could damage the actuator. To return to Drive Mode, simply
press the Mode Button again.
Delphi QR Control:
To operate the powered lift simply push the Mode Button twice to
select Actuator Mode (Fig. 56 and
bled, then the mode button needs to be pressed only once). Selec-
tion is indicated via the lighting of the Green LED adjacent to the
Mode Button. The wheelchair icon LEDs in the centre of the
Remote will light up with the currently selected Actuator Option.
Move the Joystick in the left or the right direction to scroll through
the possible options until the Lift Option is selected. Operate the
Joystick in the forward or rearward direction to move the lift up or
down. Release the Joystick when the desired angle is reached.
Once the lift is fully raised or in its lowest position do not hold the
Joystick in its operating position as this could damage the actua-
tor. To return to Drive Mode, simply press the Mode Button.
Operating the powered lift higher than 5cm from its lowest position
will bring the chair into "creep mode", moving it below will allow
full speed.
57). (If only 1 drive profile is ena-
GROOVE
13