Related Manuals for Sunrise Medical PowerTalk2
Summary of Contents for Sunrise Medical PowerTalk2
- Page 1 PowerTalk2 User Manual WheelDrive Generation 2019 Document ID: E1801_20181018_PowerTalk 2 manual WheelDrive_R2.00_BMS...
-
Page 2: Table Of Contents
PowerTalk2 User Manual Parameter List (Page� 23) 1 Introduction ������������������������������������������������ 3 7 Introduction ���������������������������������������������� 23 2 Installation PowerTalk2 ����������������������������� 4 8 Values ������������������������������������������������������� 24 8.1 Battery ............24 3 Connection ������������������������������������������������� 7 8.2 Driving Behaviour ........25 4 Interface ������������������������������������������������������ 8 9 Settings ����������������������������������������������������... -
Page 3: Introduction
PowerTalk 2 is also a service tool which gives the user an overview of system settings, sensor and parameter values, firmware versions, counters, log information and so on. The WheelDrive generation 2019 is compatible with PowerTalk 2. The software runs on Windows 10, Windows 7 and Windows XP. PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 4: Installation Powertalk2
For the installation of PowerTalk 2 on Windows 10, using the standard web browser. Visit http://powertalk.indes.eu/ Press ‘Install PowerTalk 2’. A pop-up appears requesting to save ‘setup.exe’. Save the file in a logical location. By default the file will be stored in your ‘Downloads’ directory. PowerTalk2 User Manual - E1801_20181018 Rev.A... - Page 5 ‘-‘. For example: Sunrise Medical – XXXXXX XXXXXXXXX Check and press Ok PowerTalk 2 is installed and ready for use! You can find the application through your Start Menu or on your desktop� PowerTalk2 User Manual - E1801_20181018 Rev.A...
- Page 6 When a WheelDrive of generation 1 is connected to PowerTalk 2, a pop-up box will be displayed showing that PowerTalk 1 should be used: When connecting a WheelDrive generation 2019 to PowerTalk 1, it is not possible to make a connection. PowerTalk 1 will not show a pop-up box. PowerTalk2 User Manual - E1801_20181018 Rev.A...
-
Page 7: Connection
The information that PowerTalk collects during the session will be stored on the local hard disk of the pc that is connected and this name will be used. When the same WheelDrive is connected again, the information will automatically be stored and the pop-up box below will not show up again. PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 8: Interface
Use to save the systems report to a location. The report is stored in html format. You can view the report with any browser. Send report Sends manually the report of your system to Indes. Used when service is requested from Indes. Exit Use to quit the program. PowerTalk2 User Manual - E1801_20181018 Rev.A... - Page 9 Language Use to change the language of PowerTalk interface. Dutch or English is available. Autoconnect Use to skip the login screen. When set, PowerTalk2 will automatically connect to your system. The setting is stored in the application, user independent. Help Documentation Use to find more documentation about products that can be connected to PowerTalk.
- Page 10 Note: When the WheelDrive is connected to PowerTalk and an internet connection is available, a status report will automatically be send to Indes. This field displays the Service ID and the Product serial number of the system connected. These are unique numbers for each system. PowerTalk2 User Manual - E1801_20181018 Rev.A...
-
Page 11: Tabs
This field gives date and time from the WheelDrive internal clock. The clock will be automatically synchronized when if deviates for more than 1 minute. This field shows when the next periodic check needs to be executed. PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 12: Activity
Assist and Drive rim. 2. This field graphically displays the usage of counters mentioned above and related to the expected life-time. When pointing with the cursor over the green or grey rows, detailed information is displayed, e.g.: PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 13: Values
The “Values” tab gives information about the parameter values stored in the battery pack and in the WheelDrive controller (driving behaviour). This information can be used to analyse the battery and system status. Detailed information about the parameter values can be found in this document: E1801_yyyymmdd_WheelDrive Gen 2018 parameter list_Rx.xx_yyy Example: PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 14: Settings
Undo changes: The last written settings are filled in, all changes will be undone. • Write: All changes are written to the wheel. Number behind write indicates the number of changes made before written. PowerTalk2 User Manual - E1801_20181018 Rev.A... - Page 15 Max. speed forward: This determines the max. speed you can reach with the drive rim on flat surfaces. The maximum speed is 6 km/u, corresponding with value 6. PowerTalk2 User Manual - E1801_20181018 Rev.A...
- Page 16 3. Press save and select a location. Steps to load: Press load setting Select and open a file Note: All changed fields are highlighted green Write the settings to the wheel by pressing button Write on the bottom. PowerTalk2 User Manual - E1801_20181018 Rev.A...
- Page 17 Write the settings to the wheel by pressing button Write on the bottom. Do the same for the second wheel. (see paragraph “save and load settings” for an exact copy of the settings to the second wheel). PowerTalk2 User Manual - E1801_20181018 Rev.A...
- Page 18 This field displays the battery settings. These settings are defined by the manufacturer and cannot be adjusted. The settings give general information about the battery and can be useful during service. The complete list of battery settings is displayed below: PowerTalk2 User Manual - E1801_20181018 Rev.A...
-
Page 19: Counters
Field display the counter number • Field displays if a counter can be reset to zero. By clicking the arrow symbol, the values will be reset. [L3] Note: These fields are also available for driving behaviour. PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 20: Log
The “Event” field shows the description of the event that was stored. The description always starts with a unique number for a pre-defined event, followed by a description and when relevant between brackets a beep signal. PowerTalk2 User Manual - E1801_20181018 Rev.A... - Page 21 A double input signal (input both rims at same time) was detected LOW POWER / >50°C Power was reduced due to detection of temperature above 50°C LOW POWER / <0°C Power was reduced due to detection of temperature below 0°C PowerTalk2 User Manual - E1801_20181018 Rev.A...
-
Page 22: Troubleshooting
Follow the instructions in this hyperlink to change the COM port number on the PC: https://thinksmartbox.com/answer/changing-the-com-port-for-a-usb-device/ Note: The comport numbers will increase every time a new WheelDrive is connected, so it is advised to start with number 1. PowerTalk2 User Manual - E1801_20181018 Rev.A... -
Page 23: Introduction
Introduction This document describes all parameters available in the ‘WheelDrive’ Generation 2019 software. These parameters can be monitored, changed or reset with PowerTalk 2. Notice! For full functionality the WheelDrive motor controller must be programmed with Main controller firmware version: 2.172 (or later). -
Page 24: Values
Values 8�1 Battery Parameter Meaning Info Last 10 cutoff reasons This value functions as a log for cut-off of the battery. In these situations, power from the battery is temporarily switched off by the battery electronics, because an unusual and potentially harmful event happened. The log fills from right to left;... -
Page 25: Driving Behaviour
8�2 Driving Behaviour Parameter Meaning Drive Current Speed This value shows the real-time speed of the WheelDrive in km/h. Actual Speed This value shows the user interface button that is chosen (1, 2 or 3). System Info Handle detection This value shows the real-time sensor value for the detection of the handle position. -
Page 26: Settings
Settings 9�1 Battery Parameter Meaning Info Manufacture date Battery management electronics ID information. Set in factory. Manufacturer name Battery management electronics ID information. Set in factory. BMS serial number Battery management electronics ID information. Set in factory. BMS device name Battery management electronics ID information. -
Page 27: Driving Behaviour
9�2 Driving Behaviour Parameter Meaning Info In this field the driving mode can be set by entering “1” for Gentle driving, “2” for Normal driving, “3” for Sport. These are the 3 predefined Mode setting. When customization is required Custom setting “4” must be set. Only when setting “4”... -
Page 28: System Info
9�4 System Info Parameter Meaning System Info The time and date that the system software for the main controller was Firmware build date created. This parameter is set by the software engineer at Indes. Manufacturer firmware The name of the firmware developer Manufacturer serial number The serial number of the motor controller. -
Page 29: Driving Behaviour
10�2 Driving Behaviour Parameter Meaning Drive This value shows the maximum driven speed with the WheelDrive in Maximum speed km/h. The value can be reset by clicking the arrow symbol. System info This value gives the number of unexpected “shut downs” of the system. This can for example happen when the battery is taken off without Unexpected power off using the on/off button on the User Interface. - Page 30 WheelDrive Parameter List - E1801_20181018 Rev.A...
- Page 31 WheelDrive Parameter List - E1801_20181018 Rev.A...
- Page 32 Bezplatná linka 800 900 809 F: +31 (0)30 – 60 55 880 E: info@sunrisemedical.nl Sunrise Medical ApS www.SunriseMedical.nl Park Allé 289 G DK-2605 Brøndby Sunrise Medical HCM B.V. Tlf. 70 22 43 49 Vossenbeemd 104 Email: info@sunrisemedical.dk 5705 CL Helmond www.SunriseMedical.dk The Netherlands T: +31 (0)492 593 888 Sunrise Medical Pty.