Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Lampert M280
Summary of Contents for Lampert M280
- Page 1 Operating manual M280 TIG pulse welding device...
- Page 2 "M280" Dear Customer, This operating manual is intended to familiarise you with the commissioning process and operation of your "M280”. Please read the operating instructions carefully and follow the advice given here diligently. Disruptions and operational faults will thus be avoided. Your personal safety, constant availability and long service life can be assured by this.
-
Page 3: Table Of Contents
“Note” identifies the product at risk from the hazard and possible damage to the equipment. Important! "Important!" designates user tips and other especially useful information. This is not a signal word for hazardous or dangerous situations. © Lampert Werktechnik GmbH 2017... -
Page 4: Field Of Application
ONLY SUPPLIED MAINS CABLE! against being unintentionally restarted. THE M280 IS A PIECE OF ELECTRICAL EQUIPMENT. NATIONAL REGULATIONS ON TESTING INTERVALS AND THE SCOPE OF REQUIRED RECURRING SAFETY-RELATED TESTS MUST BE OBSERVED. © Lampert Werktechnik GmbH 2017... -
Page 5: Hazards Of Shielding Gas Cylinders
Particular regulations apply to fire and explosion The Lampert eye protection systems with its integrated endangered spaces. LCD protective welding screen offers reliable protection against these risks and provides permanent protection from UV / IR rays in both light and dark state. -
Page 6: Description Of The Rear Of The Device
4.3 CONNECT EYE PROTECTION AND LED ILLUMINATION TO THE „M280“: The circular connector for the eye protection system and socket (3) on the rear of the „M280“ welding device and is the LED illumination should be inserted into the connecting to be tightened in place with the coupling nut (hand tight). -
Page 7: Connect Power Supply
(Fig. 27, p. 7) on the connecting cable used into the socket (28) on the front side front of the M280 and fasten in place by tightening the of the housing. 4.6 CONNECT POWER SUPPLY:... -
Page 8: Commissioning
5.2 EXPLANATION / OVERVIEW OF MENUS (Fig. Schematic diagram of user levels) ONCE IT IS SWITCHED ON, THE „M280“ STARTS UP IN ITS MAIN MENU. THE FOLLOWING USER LEVELS CAN BE NAVIGATED AFTER PRESSING THE METAL / MATERIAL BUTTON (26):... -
Page 9: Switching On The Device
Press the welding power activate or deactivate the acoustic signal that notifies the (+/-) buttons (23) triggering of the weld. • Language: The system can be toggled English by pressing the settings button (24). between German © Lampert Werktechnik GmbH 2017... -
Page 10: Selection Of The Welding Parameters
A very high power level is not with samples for beginners with the „M280“ system to find practical in the most usual circumstances. There is a... -
Page 11: Welding Instructions
FROM THE WORKPIECE. 7.2 WELDING WITH FOOT SWITCH (optional accessory) With the „M280“ switched off, connect the foot switch to the prompt by pressing any button. The device is now ready for socket (4) on the rear of the device. Switch the device on, operation. -
Page 12: Resharpening The Electrodes
Furthermore in 8. CARE OF THE SYSTEM COMPONENTS 8.1 CARE OF WELDING DEVICE • Check that the moving parts of the handpiece move Your „M280“ requires a minimum of maintenance under normal working conditions. However, it is essential that a easily. -
Page 13: Technical Data
No-load Mains Voltage at inert gas voltage voltage nominal load welding Power Power Nominal Earthing consumption consumption welding (earth) under max. under current load nominal load Cyclic Single-phase Keep away duration transformer from water factor © Lampert Werktechnik GmbH 2017... -
Page 14: Warning Notices
Poor welding characteristics Incorrect shielding gas Use inert shielding gas (Argon 4.6) Poor ignition characteristics Electrode clamped loosely in Tighten the clamping nut in the handpiece handpiece (chap.11, no.41) by hand, however, tighten firmly. © Lampert Werktechnik GmbH 2017... -
Page 15: Spare Parts List
Only for EU countries: In accordance with EU sent for recovery in an environmentally friendly manner. directive 2012/19/EU regarding the disposal of © Lampert Werktechnik GmbH 2017... -
Page 16: Ec-Declaration Of Conformity
13. EC – DECLARATION OF CONFORMITY Please find enclosed to this shipment the separate document – Declaration of Conformity. Text and illustrations represent the technical status at the time of printing. Subject to change. © Lampert Werktechnik GmbH 2017... - Page 17 WORKSHOP NEWS You are interested in the possibilities of use of our fine-welding devices? Or you are searching for one or another tip on working with your „M280“? Then just sign up for our newsletter on www.lampert.info! VISIT OUR SHOWROOM! Our video library is showing many applications from everyday goldsmith activities, our photo gallery various examples of use.
- Page 18 Born in Germany. Lampert Werktechnik GmbH Ettlebener Straße 27 D-97440 Werneck Tel. +49.9722.9459-0 mail@lampert.info www.lampert.info • • • • •...