Remote Control - Kenwood KCA-BT100 Instruction Manual

Dialing method
(For Audio receiver)
Registering to the Preset Dial
Number List
You can register up to 3 phone numbers for quick
dialing.
1
Enter the phone number you wish to
register
Enter the phone number with reference to the
following:
- <Making a Call by Entering a Phone Number>
(page 7)
- <Dialing by Using the Phone Book> (page 8)
- <Dialing by Using the Outgoing Call List> (page
8)
- <Dialing by Using the Incoming Call List> (page
9)
2
Select the button you wish to register
Press the [1] – [3] button for at least 2
seconds.
Multi-function Key System
1 Press the [NEXT] button.
Select the key function section.
2 Press the [1] ("1") – [3] ("3") button for at
least 2 seconds.
"Memory" or "MEMORY" display blinks 1 time.
3
Exit the dialing method selection mode
Press the [ATT] button for at least 1 second.
Dialing by Using the Phone Book
You can dial by using the downloaded Phone
Book.
1
Enter the Phone Book mode
Select the "INITIAL", "PH-BOOK1", "PH.BOOK", or
"PH-BOOK2" display.
Refer to <Selecting the Dialing Mode> (page 7).
If you have selected, "PH.BOK" or "PH-BOOK2",
proceed to step 4.
Multi-function Key System
Press the [2] ("PHBK") button.
Pressing this button toggles between the
following search methods:
Display Search method
"INITIAL"/ Search by the initial.
"PH-BOOK1"
"PH.BOOK"/ Search in the alphabetical order.
"PH-BOOK2" Proceed to step 4.
8
|
English
2
Select the initial to be searched for
Push the Control knob towards [4], [¢],
[FM] or [AM].
Move the cursor to the initial to be searched for.
Knob Operation
[4]/ [¢] Move to the next character.
[FM]/ [AM] Move to the next row.
3
Determine the selected initial
Press the Control knob ([38]) for at least 1
second.
4
Select the name
Push the Control knob towards [FM], [AM],
[4] or [¢].
Select the name.
Knob Operation
[FM]/ [AM] Change the name.
[4]/ [¢] Change the initial.
5
Originate a call
Press the Control knob for at least 1 second.
"CALL" or "Call" is displayed.
• To use the Phone Book, it must have been
downloaded from the cell-phone. For details, see
<Downloading the Phone Book> (page 5).
• Initials including no corresponding name will not be
displayed.
• On the control unit that displays three rows, the name
in the middle row is the selected one.
• During search, a non-accent character such as "u" is
searched for instead of an accent character such as "ü".
• Characters that the control unit cannot display
are searched for in the order in which they were
registered to the Phone Book.
Dialing by Using the Outgoing Call
List
You can dial by using the outgoing call list. Up
to ten phone numbers of the originated calls are
recorded in the outgoing call list.
1
Enter the outgoing call list mode
Select the "OUT" or "OUT-CALL" display.
Refer to <Selecting the Dialing Mode> (page 7).
2
Select a name or phone number
Push the Control knob towards [FM] or [AM].
3
Originate a call
Press the Control knob ([38]) for at least 1
second.
"CALL" or "Call" is displayed.
• The outgoing call list is the list of calls originated from
this unit. It is not the one stored in the Cell-phone
memory.
• On the control unit that displays three rows, the
phone number in the middle row is the selected one.
• Depending on the type of your control unit, "0" is
displayed for the tenth call in the outgoing call list.
Dialing by Using the Incoming Call
List
You can dial by using the incoming call list. Up
to ten phone numbers of the received calls are
stored recorded in the incoming call list.
1
Enter the incoming call list mode
Select the "IN" or "IN-CALL" display.
Refer to <Selecting the Dialing Mode> (page 7).
2
Select a name or phone number
Push the Control knob towards [FM] or [AM].
3
Originate a call
Press the Control knob ([38]) for at least 1
second.
"CALL" or "Call" is displayed.
• The incoming call list is the list of calls terminated to
this unit. It is not the one stored in the cell-phone
memory.
• On the control unit that displays three rows, the
phone number in the middle row is the selected one.
• Depending on the type of your control unit, "0" is
displayed for the tenth call in the incoming call list.

Remote control

(For Audio receiver)
Hands-free phone operations
[SRC] button*
During a call in progress: Disconnects the call.
[VOL] buttons*
During a call in progress:
Adjusts the voice volume.
[ ] button
Enters the dialing method selection mode.
During call termination: Answers the call.
[38] button*
During a call in progress:
Switches between the private talk mode and the
hands-free talk mode.
In dialing mode selection mode:
Selects a dialing method.
[¢] button*
Number dial input: Inputs "+".
[4] button*
Number dial input:
Clears the entered phone number.
[FM] button*
Number dial input: Inputs "#".
[AM] button*
Number dial input: Inputs "*".
[0] – [9] buttons*
Number dial input: Inputs a digit.
[DIRECT] button*
Starts the hands-free phone call.
Remote Control Mode selector switch
Switch to "AUD" when dialing.
• * If your remote controller has a mode selection switch,
set it to "AUD".
• Remote controllers with the [ ] button and/or
numeric buttons are available optionally. Purchase a
remote controller with a desired function.
English
9
|