Setting Up The Bluetooth Function - Kenwood KCA-BT100 Instruction Manual

Notes
• If you experience problems during installation,
consult your Kenwood dealer.
• When you purchase optional accessories, check
with your Kenwood dealer to make sure that they
work with your model and in your area.
• The illustrations of the display and the panel
appearing in this manual are examples used to
explain more clearly how the controls are used.
Therefore, what appears on the display in the
illustrations may differ from what appears on the
display on the actual equipment, and some of the
illustrations on the display may be inapplicable.
Kenwood Receivers available for this unit
The receiver units that can be used with KCA-BT100
are as follows: (As of September 2006)
Audio receiver
DPX501*, DPX701, KDC-MP532U*, KDC-MP632U*,
KDC-MP832U, KDC-X590*, KDC-X890, KDV-412*
Monitor receiver
DDX6019
For details on the compatible receivers to be
released in the future, access the following URL:
http://www.kenwood.com/
• *: Set the display character conversion function switch to
"2". For more details, see <Display Character Conversion
Function> (page 18).
About the Remote Controller
The audio receiver requires a remote controller with
numeric buttons to enter phone numbers directly.
To make a call using the remote controller, the [
button must be provided on the remote controller.
For more details, access the following URL:
http://www.kenwood.com/
• You cannot use a remote controller depending on the
type of your control unit.
4
|
English
About the Cell-phone
This unit conforms to the following Bluetooth
specifications:
Version Bluetooth Standard Ver. 12
Profile HFP (Hands Free Profile)
OPP (Object Push Profile)
For the cell-phones verified for compatibility, access
the following URL:
http://www.kenwood.com/
• The units supporting the Bluetooth function have been
certified for conformity with the Bluetooth Standard
following the procedure prescribed by Bluetooth
SIG. However, it may be impossible for such units to
communicate with your cell-phone depending on its
type.
• HFP is a profile used to make a hands-free call.
• OPP is a profile used to transfer data such as a phone
book between units.
]

Setting up the Bluetooth Function

Before Use
• You need to register your cell-phone before using
it with this unit. For more details, see <Registering
Your Cell-phone> (page 5).
• If you have registered two or more cell-phones,
you need to select one of them. For more
details, see <Selecting the Cell-phone You Wish
to Connect> (page 10) or <Hands-Free phone
Select> (page 17).
• To use the Phone Book, it must be downloaded
to this unit in advance. For details, see
<Downloading the Phone Book> (page 5).
• You can set the volume of the voice output
speaker. For more details, see <Setting up the
Voice Output Speakers> (page 11) or <Hands-Free
phone Setup> (page 16).
Registering Your Cell-phone
To make your cell-phone usable with this unit,
you need to register it (pairing). You can register
up to five cell-phones to this unit.
1
Turn on the control unit.
2
Start cell-phone registration on the cell-
phone
By operating the cell-phone, carry out hands-free
phone registration (pairing). Select "KCA-BT100"
from the list of connected units.
3
Enter a path key
Enter "1234" as a path key.
Check that registration is complete on the cell-
phone.
4
By operating the cell-phone, start hands-free
connection.
• For how to operate the cell-phone, refer to the
Instruction Manual that comes with your cell-phone.
• You can register up to five cell-phones. Registering the
sixth cell-phone will delete the cell-phone registered
most previously.
• You cannot register a cell-phone when another
cell-phone is in the hands-free connection status.
Terminate the hands-free connection, and then
register a new cell-phone.
• If two or more "KCA-BT100s" are displayed in the list
of connected units, another "KCA-BT100" is probably
used nearby. Move you car, and then check that only
one "KCA-BT100" is displayed.
Downloading the Phone Book
Download the phone book data from the cell-
phone to this unit so that you can use the Phone
Book of this unit.
1
By operating the cell-phone, terminate the
hands-free connection.
2
By operating the cell-phone, send the phone
book data to this unit
By operating the cell-phone, download the
phone book data to this unit.
During downloading:
"Downloading", "DOWNLOAD", or "Now
Downloading..." is displayed.
After completion of downloading:
"Completed" or "COMPLETE" is displayed.
3
By operating the cell-phone, start the hands-
free connection.
To clear the downloading completion
message (for Audio receiver):
Press any button.
• For how to operate the cell-phone, refer to the
Instruction Manual that comes with your cell-phone.
• Up to 300 phone numbers can be registered for each
registered cell-phone.
• Up to 32 digits can be registered for each phone
number along with up to 40 characters representing a
name.
• Depending on the type of your cell-phone, the
following restrictions are placed:
- The phone book data cannot be downloaded
normally.
- Characters in the Phone Book are garbled.
- The phone book data cannot be downloaded
normally if it contains images. It may take several
hours to a full day to download the phone book
depending on the total image size.
• To cancel downloading of the phone book data,
operate the cell-phone.
English
5
|